Comparison of machinability aluminium alloy LM6 when using coated and uncoated carbide cutting tool.
COMPARISON OF MACHINABILITY ALUMINIUM ALLOY LM6
WHEN USING COATED AND UNCOATED CARBIDE CUTTING
TOOL
KHUZAIMI BIN MOHD ARIS
A thesis submitted
in fulfillment of the requirements for the degree of Master of
Manufacturing Engineering (Industrial Engineering).
Faculty of Manufacturing Engineering
UNIVERSITI TEKNIKAL MALAYSIA MELAKA
2014
© Universiti Teknikal Malaysia Melaka
UNIVERSITI TEKNIKAL MALAYSIA MELAKA
Faculty of Manufacturing Engineering
COMPARISON OF MACHINABILITY ALUMINIUM ALLOY
LM6 WHEN USING COATED AND UNCOATED CARBIDE
CUTTING TOOL
Khuzaimi Bin Mohd Aris
Master of Manufacturing Engineering
(Industrial Engineering).
2014
© Universiti Teknikal Malaysia Melaka
COMPARISON OF MACHINABILITY ALUMINIUM ALLOY LM6
WHEN USING COATED AND UNCOATED CARBIDE CUTTING
TOOL
KHUZAIMI BIN MOHD ARIS
A thesis submitted
in fulfillment of the requirements for the degree of Master of
Manufacturing Engineering (Industrial Engineering).
Faculty of Manufacturing Engineering
UNIVERSITI TEKNIKAL MALAYSIA MELAKA
2014
© Universiti Teknikal Malaysia Melaka
DECLARATION
I declare that this thesis entitled "Comparison of Machinability Aluminium Alloy
LM6 When Using Coated and Uncoated Carbide Cutting Tool" is the result of my
own research except as cited in the references. The thesis has not been accepted for
any degree and is not concurrently submitted in candidature of any other degree.
セ@
HGjaャ|セ
ᄋ@
Signature
: ................
Name
: KHUZAIMl BIN MOHD ARIS
Date
:... ... jセNO_MZ
© Universiti Teknikal Malaysia Melaka
................... .
N セエ@
. . . . . . ....
APPROVAL
I hereby declare that I have read this dissertation/report and in my opinion this
dissertation/report is sufficient in terms of scope and quality as a partial fulfillment of
Master of Manufacturing Engineering (Industrial Engineering).
Signature
Supervisor Name
: DR m
\_セッEスjォヲゥャGwキN。@
Pensyarah Kanen
'"a1'ult1 Kejuruteraan Pembuatan
BAKAR ,>niversili Tekn1kal Malaysia Melali.a
Hang 1 uah Java
11;:·0r OuriRr.., ·111ggal M
Date
:...i;;._77201
WHEN USING COATED AND UNCOATED CARBIDE CUTTING
TOOL
KHUZAIMI BIN MOHD ARIS
A thesis submitted
in fulfillment of the requirements for the degree of Master of
Manufacturing Engineering (Industrial Engineering).
Faculty of Manufacturing Engineering
UNIVERSITI TEKNIKAL MALAYSIA MELAKA
2014
© Universiti Teknikal Malaysia Melaka
UNIVERSITI TEKNIKAL MALAYSIA MELAKA
Faculty of Manufacturing Engineering
COMPARISON OF MACHINABILITY ALUMINIUM ALLOY
LM6 WHEN USING COATED AND UNCOATED CARBIDE
CUTTING TOOL
Khuzaimi Bin Mohd Aris
Master of Manufacturing Engineering
(Industrial Engineering).
2014
© Universiti Teknikal Malaysia Melaka
COMPARISON OF MACHINABILITY ALUMINIUM ALLOY LM6
WHEN USING COATED AND UNCOATED CARBIDE CUTTING
TOOL
KHUZAIMI BIN MOHD ARIS
A thesis submitted
in fulfillment of the requirements for the degree of Master of
Manufacturing Engineering (Industrial Engineering).
Faculty of Manufacturing Engineering
UNIVERSITI TEKNIKAL MALAYSIA MELAKA
2014
© Universiti Teknikal Malaysia Melaka
DECLARATION
I declare that this thesis entitled "Comparison of Machinability Aluminium Alloy
LM6 When Using Coated and Uncoated Carbide Cutting Tool" is the result of my
own research except as cited in the references. The thesis has not been accepted for
any degree and is not concurrently submitted in candidature of any other degree.
セ@
HGjaャ|セ
ᄋ@
Signature
: ................
Name
: KHUZAIMl BIN MOHD ARIS
Date
:... ... jセNO_MZ
© Universiti Teknikal Malaysia Melaka
................... .
N セエ@
. . . . . . ....
APPROVAL
I hereby declare that I have read this dissertation/report and in my opinion this
dissertation/report is sufficient in terms of scope and quality as a partial fulfillment of
Master of Manufacturing Engineering (Industrial Engineering).
Signature
Supervisor Name
: DR m
\_セッEスjォヲゥャGwキN。@
Pensyarah Kanen
'"a1'ult1 Kejuruteraan Pembuatan
BAKAR ,>niversili Tekn1kal Malaysia Melali.a
Hang 1 uah Java
11;:·0r OuriRr.., ·111ggal M
Date
:...i;;._77201