template for journal KAPAL
PAPER TITLE
A. Unknown, Naval Architecture Department, Diponegoro University
B. Goodman & C. Fineman, Naval Architecture Department, Diponegoro University
ABSTRACT
This document is the Microsoft Word template for the Journal of KAPAL. The formatting and arrangement of
this text conforms exactly to the requirements for all Technical Paper submissions. All papers require an
Abstract section at the beginning; this is a brief description of the scope of the work. This first section of the
paper takes 16 cm of the page and is 1 column, Font 10, Times New Roman, Aligned Justified, as this
paragraph. The subsequent sections should use a two-column setup, as below with Font 12, Times New Roman,
Regular, Justified. If you need to alternate between full width and two-columns (perhaps to insert large pictures
or tables) use ‘Continuous Section Breaks’ to separate the text. The Styles and Formatting toolbar (which has
been pre-set in this document) can be activated using the button in the top toolbar marked with a blue ‘double-A’
symbol. Formatting within the document can be made visible by using the button in the top toolbar marked with
this symbol.
Keyword: stability, manoeuvring, propeller
NOMENCLATURE
3. LISTS
This is required for all
papers using a large
number of symbols,
abbreviations
or
acronyms. From this
point onwards the rest
of the document is in
Font 12, Times New
Roman, Regular, and
Aligned Justified.
Bullet points should be
used for lists:
Not numbers or
letters
-Hyphens are used
for
second-level
indents
1.
The Figure No. and
details of the figure
must be given at
bottom of each figure
in Font 10, Times New
Roman,
Regular.
Similarly
for
the
Table, Table No and
other
information
should be mentioned
on the Top of the table,
Font 12, BOLD, Times
Roman.
INTRODUCTI
ON
This is normally the
first section in the
paper. The length of
this paper is limited up
to maximum of 10
pages.
2. HEADING
4. FIGURES &
TABLES
The heading should be
in BOLD CAPITAL,
Font 12, Times New
Roman.
5.
2.1
The main body of the
text must end with the
conclusions of the
paper.
SUB-HEADING
Sub heading should be
Regular,
CAPITAL,
Font 12, Times New
Roman
2.1 (a) Further
Subsidiary
Heading
Headings
should
follow the convention
above; with numbers
added manually and a
single ‘tab’ used to
space out the title.
CONCLUSION
S
ACKNOWLEDGE
MENTS
Brief
acknowledgements, or
a disclaimer, may be
included at the end of
the paper and its
heading shouldn’t be
numbered.
REFERENCES
References should be
numbered in the text
where they occur, with
the number in square
brackets [1] and a
complete list given at
the end of the paper:
1. [AUTHORS],[Year]
‘[Title of Reference]’,
[Source of Reference,
Vol. No., pp etc.]
A. Unknown, Naval Architecture Department, Diponegoro University
B. Goodman & C. Fineman, Naval Architecture Department, Diponegoro University
ABSTRACT
This document is the Microsoft Word template for the Journal of KAPAL. The formatting and arrangement of
this text conforms exactly to the requirements for all Technical Paper submissions. All papers require an
Abstract section at the beginning; this is a brief description of the scope of the work. This first section of the
paper takes 16 cm of the page and is 1 column, Font 10, Times New Roman, Aligned Justified, as this
paragraph. The subsequent sections should use a two-column setup, as below with Font 12, Times New Roman,
Regular, Justified. If you need to alternate between full width and two-columns (perhaps to insert large pictures
or tables) use ‘Continuous Section Breaks’ to separate the text. The Styles and Formatting toolbar (which has
been pre-set in this document) can be activated using the button in the top toolbar marked with a blue ‘double-A’
symbol. Formatting within the document can be made visible by using the button in the top toolbar marked with
this symbol.
Keyword: stability, manoeuvring, propeller
NOMENCLATURE
3. LISTS
This is required for all
papers using a large
number of symbols,
abbreviations
or
acronyms. From this
point onwards the rest
of the document is in
Font 12, Times New
Roman, Regular, and
Aligned Justified.
Bullet points should be
used for lists:
Not numbers or
letters
-Hyphens are used
for
second-level
indents
1.
The Figure No. and
details of the figure
must be given at
bottom of each figure
in Font 10, Times New
Roman,
Regular.
Similarly
for
the
Table, Table No and
other
information
should be mentioned
on the Top of the table,
Font 12, BOLD, Times
Roman.
INTRODUCTI
ON
This is normally the
first section in the
paper. The length of
this paper is limited up
to maximum of 10
pages.
2. HEADING
4. FIGURES &
TABLES
The heading should be
in BOLD CAPITAL,
Font 12, Times New
Roman.
5.
2.1
The main body of the
text must end with the
conclusions of the
paper.
SUB-HEADING
Sub heading should be
Regular,
CAPITAL,
Font 12, Times New
Roman
2.1 (a) Further
Subsidiary
Heading
Headings
should
follow the convention
above; with numbers
added manually and a
single ‘tab’ used to
space out the title.
CONCLUSION
S
ACKNOWLEDGE
MENTS
Brief
acknowledgements, or
a disclaimer, may be
included at the end of
the paper and its
heading shouldn’t be
numbered.
REFERENCES
References should be
numbered in the text
where they occur, with
the number in square
brackets [1] and a
complete list given at
the end of the paper:
1. [AUTHORS],[Year]
‘[Title of Reference]’,
[Source of Reference,
Vol. No., pp etc.]