High-Resolution Conversion of Light Intensity to Frequency

  PACKAGE D High-Resolution Conversion of Light D

  8-LEAD SOIC Intensity to Frequency (TOP VIEW) Programmable Color and Full-Scale Output

  D Frequency

  S0

  1

  8 S3 Communicates Directly With a Microcontroller

  D S1 2

  7 S2 Single-Supply Operation (2.7 V to 5.5 V)

  D Power Down Feature

  OE 3

  6 OUT D Nonlinearity Error Typically 0.2% at 50 kHz

  D GND 4

  5 V DD Stable 200 ppm/ °C Temperature Coefficient

  D TCS3200 Low-Profile Lead (Pb) Free and RoHS

  D Compliant Surface-Mount Package

  S0

  1

  8 S3 Description

  S1 2

  7 S2 The TCS3200 and TCS3210 programmable color

  OE 3

  6 OUT light-to-frequency converters that combine confi- gurable silicon photodiodes and a current-to-fre-

  GND 4

  5 V DD quency converter on a single monolithic CMOS

  TCS3210 integrated circuit. The output is a square wave (50% duty cycle) with frequency directly propor- tional to light intensity (irradiance).

  The full-scale output frequency can be scaled by one of three preset values via two control input pins. Digital inputs and digital output allow direct interface to a microcontroller or other logic circuitry. Output enable (OE)

places the output in the high-impedance state for multiple-unit sharing of a microcontroller input line.

In the TCS3200, the light-to-frequency converter reads an 8 x 8 array of photodiodes. Sixteen photodiodes have blue filters, 16 photodiodes have green filters, 16 photodiodes have red filters, and 16 photodiodes are clear with no filters. In the TCS3210, the light-to-frequency converter reads a 4 x 6 array of photodiodes. Six photodiodes have blue filters, 6 photodiodes have green filters, 6 photodiodes have red filters, and 6 photodiodes are clear with no filters. The four types (colors) of photodiodes are interdigitated to minimize the effect of non-uniformity of incident irradiance. All photodiodes of the same color are connected in parallel. Pins S2 and S3 are used to select which group of photodiodes (red, green, blue, clear) are active. Photodiodes are 110 µm x 110 µm in size and are on 134- µm centers.

  Functional Block Diagram Output Current-to-Frequency Photodiode Light Converter Array S2 S3 S0 S1 OE Copyright E 2009, TAOS Inc. The LUMENOLOGY r Company

  r

Texas Advanced Optoelectronic Solutions Inc.

  

1001 Klein Road S Suite 300 S Plano, TX 75074 S (972) 673-0759 r Copyright E 2009, TAOS Inc.

  The LUMENOLOGY r Company Terminal Functions TERMINAL I/O DESCRIPTION NAME NO. I/O DESCRIPTION

  GND 4 Power supply ground. All voltages are referenced to GND. OE

  3 I Enable for f

  o (active low).

  OUT 6 O Output frequency (f o ). S0, S1 1, 2 I Output frequency scaling selection inputs. S2, S3 7, 8 I Photodiode type selection inputs.

  V DD

  5 Supply voltage

  

Table 1. Selectable Options

S0 S1 OUTPUT FREQUENCY SCALING (f

o

  ) S2 S3 PHOTODIODE TYPE

  L L Power down L L Red

  L H 2% L H Blue H L 20% H L Clear (no filter) H H 100% H H Green

  Available Options DEVICE T A PACKAGE − LEADS PACKAGE DESIGNATOR ORDERING NUMBER

  TCS3200 −40 °C to 85°C SOIC−8 D TCS3200D TCS3210 −40 °C to 85°C SOIC−8 D TCS3210D

  The LUMENOLOGY r Company

  5 µA

  −40 70 °C

  Electrical Characteristics at T A = 25 °C, V

  DD = 5 V (unless otherwise noted) PARAMETER TEST CONDITIONS MIN TYP MAX UNIT

  V OH High-level output voltage

  I OH = − 2 mA

  4

  4.5 V

  V OL Low-level output voltage

  I OL = 2 mA

  0.25

  0.40 V

  I IH High-level input current

  I IL Low-level input current

  0.8 V Operating free-air temperature range, T

  5 µA

  I Supply current Power-on mode

  1.4 2 mA

  I DD Supply current

  Power-down mode 0.1 µA S0 = H, S1 = H 500 600 kHz

   S0 = H, S1 = L 100 120 kHz

  Full scale frequency (See Note S0 = L, S1 = H

  10 12 kHz Temperature coefficient of responsivity

  λ ≤ 700 nm, −25°C ≤ T

  A

  ≤ 70°C ± 200 ppm/ °C k

  SVS

  Supply voltage sensitivity

  A

  V DD = 2.7 V to 5.5 V

  r Copyright E 2009, TAOS Inc.

  †

  

Absolute Maximum Ratings over operating free-air temperature range (unless otherwise noted)

  Supply voltage, V

  DD

   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 V Input voltage range, all inputs, V

  I

  −0.3 V to V

  DD + 0.3 V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

  Operating free-air temperature range, T

  A

   −40 °C to 85°C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

  Storage −40 °C to 85°C

  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Solder 260 °C

  . . .

  Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. NOTES: 1. All voltage values are with respect to GND.

  IL

  2. Long-term storage or operation above 70 °C could cause package yellowing that will lower the sensitivity to wavelengths < 500nm.

  3. The device may be hand soldered provided that heat is applied only to the solder pad and no contact is made between the tip of the solder iron and the device lead. The maximum time heat should be applied to the device is 5 seconds.

  Recommended Operating Conditions MIN NOM MAX UNIT

  Supply voltage, V

  DD

  2.7

  5

  5.5 V High-level input voltage, V

  IH

  V DD = 2.7 V to 5.5 V

  2 V

  DD

  V Low-level input voltage, V

  V DD = 5 V ±10% ±0.5 %/ V NOTE 4: Full-scale frequency is the maximum operating frequency of the device without saturation.

C, S0 = H, S1 = H (unless otherwise noted) (See Notes 5, 6, 7, and 8). Values for TCS3200 (TCS3210) are below. PARAMETER TEST CONDITIONS CLEAR PHOTODIODE S2 = H, S3 = L BLUE PHOTODIODE S2 = L, S3 = H GREEN PHOTODIODE S2 = H, S3 = H RED PHOTODIODE S2 = L, S3 = L UNIT CONDITIONS MIN TYP MAX MIN TYP MAX MIN TYP MAX MIN TYP MAX

  (4839) −− −− −−

  −− −− −− f

  = 640 nm (3371)

  p

  1266 λ

  (Note 11) λ 640 nm

  2

  −− −− −− µW/ cm

  = 524 nm (4138)

  p

  λ

  µW/ irradiance (Note 11)

  Saturation irradiance λ 524 nm 1554

  p = 470 nm

  Dark frequency E

  λ

  λ 470 nm 1813

  (178) 5% 21% 0% 12% 84% 105%

  p = 640 nm

  ) λ

  2

  474 5% 21% 0% 12% 84% 105% cm

  ) (Note 10) λ 640 nm

  2

  8% 28% 57% 80% 9% 27% ( µW/ cm

  = 524 nm (145)

  p

  D

  e

  responsivity (Note 10)

  NOTES: 5. Optical measurements are made using small-angle incident radiation from a light-emitting diode (LED) optical source.

  O from a straight line between zero and full scale, expressed as a percent of full scale.

  12. Nonlinearity is defined as the deviation of f

  11. Saturation irradiance = (full-scale frequency)/(irradiance responsivity) for the Clear reference channel.

  e is characterized over the range from zero to 5 kHz.

  10. Irradiance responsivity R

  9. Output frequency Blue, Green, Red percentage represents the ratio of the respective color to the Clear channel absolute value.

  p = 640 nm, spectral halfwidth Δλ½ = 17 nm, and luminous efficacy = 155 lm/W.

  8. The 640 nm input irradiance is supplied by a AlInGaP light-emitting diode with the following characteristics: peak wavelength λ

  p = 524 nm, spectral halfwidth Δλ½ = 47 nm, and luminous efficacy = 520 lm/W.

  7. The 524 nm input irradiance is supplied by an InGaN light-emitting diode with the following characteristics: peak wavelength λ

  p = 470 nm, spectral halfwidth Δλ½ = 35 nm, and luminous efficacy = 75 lm/W.

  6. The 470 nm input irradiance is supplied by an InGaN light-emitting diode with the following characteristics: peak wavelength λ

  µs Response time to out- put enable (OE) 100 100 100 100 ns

  = 0

  ± 0.5 ± 0.5 ± 0.5 ± 0.5 % F.S. Recovery from power down 100 100 100 100

  = 0 to 50 kHz ± 0.2 ± 0.2 ± 0.2 ± 0.2 % F.S. (Note 12) f O = 0 to 500 kHz

  O

  Nonlinearity (Note 12) f

  10 Hz f O = 0 to 5 kHz ± 0.1 ± 0.1 ± 0.1 ± 0.1

  2

  10

  2

  10

  2

  10

  2

  λ

  r Copyright E 2009, TAOS Inc.

  The LUMENOLOGY r Company Operating Characteristics at V DD = 5 V, T A = 25 °

  p

  frequency (Note

  O

  18.7 8% 28% 57% 80% 9% 27% kHz f

  15.6

  12.5

  ,

  2

  = 40.4 µW/cm

  e

  E

  61% 84% 22% 43% 0% 6% f Output frequency

  = 470 nm (4.7) (5.85) (7)

  , λ

  e

  2

  = 47.2 µW/cm

  e

  E

  18.7 61% 84% 22% 43% 0% 6%

  15.6

  12.5

  ,

  2

  = 47.2 µW/cm

  e

  E

  E

  = 40.4 µW/cm

  Hz/ ( W/ R

  e

  386 8% 28% 57% 80% 9% 27%

  Irradiance responsivity λ 524 nm

  61% 84% 22% 43% 0% 6% R

  = 470 nm (124)

  p

  331 61% 84% 22% 43% 0% 6% λ

  5% 21% 0% 12% 84% 105% λ 470 nm

  = 640 nm (4.9) (6.15) (7.4)

  p

  , λ

  2

  = 34.6 µW/cm

  E

  2

  19.7 5% 21% 0% 12% 84% 105%

  16.4

  13.1

  ,

  2

  = 34.6 µW/cm

  e

  E

  8% 28% 57% 80% 9% 27% kHz (Note

  = 524 nm (4.7) (5.85) (7)

  p

  , λ

  e

  

TYPICAL CHARACTERISTICS

NORMALIZED OUTPUT FREQUENCY PHOTODIODE SPECTRAL RESPONSIVITY vs.

ANGULAR DISPLACEMENT

  1

  1 Normalized to Clear

  0.9 @ 715 nm Blue

  0.8

  0.8 Clear

  °C

  T A = 25

  0.7 Red Green

  0.6

  0.6 Blue

  0.5 Optical Axis

  0.4

  0.4

  0.3 Relative Responsivity

  0.2 0.2 — Output Frequency — Normalized O f Angular Displacement is

  0.1 Green Equal for Both Aspects 300 500 700 900 1100 90 −90 −60 −30

  30

  60

  λ − Wavelength − nm Q

   − Angular Displacement − ° Figure 1

  Figure 2 I vs. DD NORMALIZED OUTPUT V vs. DD vs. TEMPERATURE

  V DD

  1.55 100.6

  1.5 100.4

1.45 Saturated

  V DD = 5 V

  1.4 100.2

  1.35

  1.3 Saturated 100

  V DD = 3 V — mA

  1.25 DD

  I

  1.2

  99.8 Normalized Output — %

  1.15 Dark

  1.1

  99.6 V = 3 V DD Dark

  1.05 V DD = 5 V

  99.4

  1

  2.5

  3

  3.5

  4

  4.5

  5

  5.5

  25

  50 75 100

  °C

  T A − Free-Air Temperature − V − V

  DD Figure 3 Figure 4 Copyright E 2009, TAOS Inc. The LUMENOLOGY r Company

  r

  

TYPICAL CHARACTERISTICS

PHOTODIODE RESPONSIVITY TEMPERATURE COEFFICIENT

vs.

WAVELENGTH OF INCIDENT LIGHT

  9k 8k 7k 6k 5k 4k Coefficient — ppm/deg C 3k 2k emperature 1k T

600 650 700 750 800 850 900 950 1000

  λ − Wavelength of Incident Light − nm

  Figure 5 Copyright E 2009, TAOS Inc.

  The LUMENOLOGY r Company

  r

  

APPLICATION INFORMATION

Power supply considerations µF to 0.1-µF capacitor with short leads mounted close to the Power-supply lines must be decoupled by a 0.01- device package.

  Input interface A low-impedance electrical connection between the device OE pin and the device GND pin is required for improved noise immunity. All input pins must be either driven by a logic signal or connected to VDD or GND — they should not be left unconnected (floating).

  Output interface The output of the device is designed to drive a standard TTL or CMOS logic input over short distances. If lines greater than 12 inches are used on the output, a buffer or line driver is recommended.

  A high state on Output Enable (OE) places the output in a high-impedance state for multiple-unit sharing of a microcontroller input line.

  Power down Powering down the sensor using S0/S1 (L/L) will cause the output to be held in a high-impedance state. This is similar to the behavior of the output enable pin, however powering down the sensor saves significantly more power than disabling the sensor with the output enable pin.

  Photodiode type (color) selection The type of photodiode (blue, green, red, or clear) used by the device is controlled by two logic inputs, S2 and S3

  Output frequency scaling Output-frequency scaling is controlled by two logic inputs, S0 and S1. The internal light-to-frequency converter generates a fixed-pulsewidth pulse train. Scaling is accomplished by internally connecting the pulse-train output of the converter to a series of frequency dividers. Divided outputs are 50%-duty cycle square waves with relative frequency values of 100%, 20%, and 2%. Because division of the output frequency is accomplished by counting pulses of the principal internal frequency, the final-output period represents an average of the multiple periods of the principle frequency.

  The output-scaling counter registers are cleared upon the next pulse of the principal frequency after any transition of the S0, S1, S2, S3, and OE lines. The output goes high upon the next subsequent pulse of the principal frequency, beginning a new valid period. This minimizes the time delay between a change on the input lines and the resulting new output period. The response time to an input programming change or to an irradiance step change is one period of new frequency plus 1 µs. The scaled output changes both the full-scale frequency and the dark frequency by the selected scale factor.

  The frequency-scaling function allows the output range to be optimized for a variety of measurement techniques. The scaled-down outputs may be used where only a slower frequency counter is available, such as low-cost microcontroller, or where period measurement techniques are used.

  Copyright E 2009, TAOS Inc.

  The LUMENOLOGY r Company

  r

  

APPLICATION INFORMATION

Measuring the frequency The choice of interface and measurement technique depends on the desired resolution and data acquisition rate. For maximum data-acquisition rate, period-measurement techniques are used. Output data can be collected at a rate of twice the output frequency or one data point every microsecond for full-scale output. Period measurement requires the use of a fast reference clock with available resolution directly related to reference clock rate. Output scaling can be used to increase the resolution for a given clock rate or to maximize resolution as the light input changes. Period measurement is used to measure rapidly varying light levels or to make a very fast measurement of a constant light source. Maximum resolution and accuracy may be obtained using frequency-measurement, pulse-accumulation, or integration techniques. Frequency measurements provide the added benefit of averaging out random- or high-frequency variations (jitter) resulting from noise in the light signal. Resolution is limited mainly by available counter registers and allowable measurement time. Frequency measurement is well suited for slowly varying or constant light levels and for reading average light levels over short periods of time. Integration (the accumulation of pulses over a very long period of time) can be used to measure exposure, the amount of light present in an area over a given time period.

  PCB Pad Layout Suggested PCB pad layout guidelines for the

  4.65

  6.90

  1.27

  2.25

  0.50 NOTES: A. All linear dimensions are in millimeters.

  B. This drawing is subject to change without notice.

  

Figure 6. Suggested D Package PCB Layout

Copyright E 2009, TAOS Inc.

  The LUMENOLOGY r Company

  r

MECHANICAL INFORMATION

  

This SOIC package consists of an integrated circuit mounted on a lead frame and encapsulated with an electrically

nonconductive clear plastic compound. The TCS3200 has an 8 × 8 array of photodiodes with a total size of 1 mm

µm µm in size and are positioned on 134 µm centers. by 1 mm. The photodiodes are 110 × 110 PACKAGE D

  PLASTIC SMALL-OUTLINE NOTE B TOP VIEW BOTTOM VIEW

  2.12 3.00 + 0.250 0.250

  • PIN 1

  PIN 1 0.510 y

  8 y

  6

   1.27 0.330 SIDE VIEW

  j

2.8 TYP CLEAR WINDOW

  5.00 END VIEW

  4.80

  5.3 MAX

  0.50

0.88 TYP TOP OF

  0.25 455 SENSOR DIE

  A

  1.75

1.35 DETAIL A

  4.00

  3.80

  6.20

  5.80

  0.25

  0.19

  1.27

  0.41

  0.25 Pb

  0.10 NOTES: A. All linear dimensions are in millimeters.

  B. The center of the 1-mm by 1-mm photo-active area is referenced to the upper left corner tip of the lead frame (Pin 1).

  C. Package is molded with an electrically nonconductive clear plastic compound having an index of refraction of 1.55.

  D. This drawing is subject to change without notice.

  

Figure 7. Package D — TCS3200 Plastic Small Outline IC Packaging Configuration

Copyright E 2009, TAOS Inc.

  The LUMENOLOGY r Company

  r

MECHANICAL INFORMATION

  

This SOIC package consists of an integrated circuit mounted on a lead frame and encapsulated with an electrically

nonconductive clear plastic compound. The TCS3210 has a 4 × 6 array of photodiodes with a total size of 0.54 mm

µm µm in size and are positioned on 134 µm centers. by 0.8 mm. The photodiodes are 110 × 110 PACKAGE D

  PLASTIC SMALL-OUTLINE NOTE B TOP VIEW BOTTOM VIEW

  2.12 3.00 + 0.250 0.250

  • PIN 1

  PIN 1 0.510 y

  8 y

  6

   1.27 0.330 SIDE VIEW

  j

2.8 TYP CLEAR WINDOW

  5.00 END VIEW

  4.80

  5.3 MAX

  0.50

0.88 TYP TOP OF

  0.25 455 SENSOR DIE

  A

  1.75

1.35 DETAIL A

  4.00

  3.80

  6.20

  5.80

  0.25

  0.19

  1.27

  0.41

  0.25 Pb

  0.10 NOTES: A. All linear dimensions are in millimeters.

  B. The center of the 0.54-mm by 0.8-mm photo-active area is referenced to the upper left corner tip of the lead frame (Pin 1).

  C. Package is molded with an electrically nonconductive clear plastic compound having an index of refraction of 1.55.

  D. This drawing is subject to change without notice.

  

Figure 8. Package D — TCS3210 Plastic Small Outline IC Packaging Configuration

Copyright E 2009, TAOS Inc.

  The LUMENOLOGY r Company

  r

  

MECHANICAL INFORMATION

SIDE VIEW K 2.11 + 0.10 [0.083 + 0.004] o 0.292 + 0.013 [0.0115 + 0.0005] END VIEW TOP VIEW 8 + 0.1 4 + 0.1 2 + 0.05

  j

  1.50 1.75 + 0.10

  [0.315 + [0.157 + [0.079 + [0.069 + 0.004] 0.004] 0.004] 0.002] B 5.50 + 0.05 [0.217 + 0.002] 12 + 0.3 − 0.1 [0.472 + 0.12 − 0.004] B A A DETAIL A DETAIL B 6.45 + 0.10 5.13 + 0.10 [0.254 + 0.004] [0.202 + 0.004] A

  B o o NOTES: A. All linear dimensions are in millimeters [inches].

  B. The dimensions on this drawing are for illustrative purposes only. Dimensions of an actual carrier may vary slightly.

  C. Symbols on drawing A , B , and K are defined in ANSI EIA Standard 481−B 2001.

  o o o D. Each reel is 178 millimeters in diameter and contains 1000 parts.

  E. TAOS packaging tape and reel conform to the requirements of EIA Standard 481−B.

  F. This drawing is subject to change without notice.

  

Figure 9. Package D Carrier Tape

Copyright E 2009, TAOS Inc.

  The LUMENOLOGY r Company

  r

MANUFACTURING INFORMATION

  3 Max 10 sec

  5C)

Figure 10. TCS3200, TCS3210 Solder Reflow Profile Graph

  Time (sec) T emperature (

  Not to scale — for reference only

  1 T peak

  2 T

  3 T

  1 t soak T

  2 t

  3 t

  t

  Temperature gradient in cooling Max −5 °C/sec

  Peak temperature in reflow T peak 260 ° C (−0°C/+5°C)

  r Copyright E 2009, TAOS Inc.

  The LUMENOLOGY r Company

  peak

  Time above T

  2 Max 50 sec

  Time above 230 °C t

  1 Max 60 sec

  2 to 3 minutes Time above 217 °C t

  soak

  Soak time t

  2.5 °C/sec

  Average temperature gradient in preheating

  

Table 2. TCS3200, TCS3210 Solder Reflow Profile

PARAMETER REFERENCE TCS32x0

  The Plastic Small Outline IC package (D) has been tested and has demonstrated an ability to be reflow soldered to a PCB substrate. The solder reflow profile describes the expected maximum heat exposure of components during the solder reflow process of product on a PCB. Temperature is measured on top of component. The component should be limited to a maximum of three passes through this solder reflow profile.

  −10 °C t

  Moisture Sensitivity Optical characteristics of the device can be adversely affected during the soldering process by the release and vaporization of moisture that has been previously absorbed into the package molding compound. To prevent these adverse conditions, all devices shipped in carrier tape have been pre-baked and shipped in a sealed moisture-barrier bag. No further action is necessary if these devices are processed through solder reflow within 24 hours of the seal being broken on the moisture-barrier bag. However, for all devices shipped in tubes or if the seal on the moisture barrier bag has been broken for 24 hours or longer, it is recommended that the following procedures be used to ensure the package molding compound contains the smallest amount of absorbed moisture possible.

  For devices shipped in tubes:

  1. Remove devices from tubes

  2. Bake devices for 4 hours, at 90 °C

  3. After cooling, load devices back into tubes

  4. Perform solder reflow within 24 hours after bake Bake only a quantity of devices that can be processed through solder reflow in 24 hours. Devices can be re-baked for 4 hours, at 90 °C for a cumulative total of 12 hours (3 bakes for 4 hours at 90°C).

  For devices shipped in carrier tape: °C in the tape

  1. Bake devices for 4 hours, at 90

  2. Perform solder reflow within 24 hours after bake Bake only a quantity of devices that can be processed through solder reflow in 24 hours. Devices can be °C for a cumulative total of 12 hours (3 bakes for 4 hours at 90°C). re−baked for 4 hours in tape, at 90 Copyright E 2009, TAOS Inc.

  The LUMENOLOGY r Company

  r

  PRODUCTION DATA — information in this document is current at publication date. Products conform to specifications in accordance with the terms of Texas Advanced Optoelectronic Solutions, Inc. standard warranty. Production processing does not necessarily include testing of all parameters.

  LEAD-FREE (Pb-FREE) and GREEN STATEMENT Pb-Free (RoHS) TAOS’ terms Lead-Free or Pb-Free mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TAOS Pb-Free products are suitable for use in specified lead-free processes.

  Green (RoHS & no Sb/Br) TAOS defines Green to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material). Important Information and Disclaimer The information provided in this statement represents TAOS’ knowledge and belief as of the date that it is provided. TAOS bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TAOS has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TAOS and TAOS suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.

  NOTICE Texas Advanced Optoelectronic Solutions, Inc. (TAOS) reserves the right to make changes to the products contained in this document to improve performance or for any other purpose, or to discontinue them without notice. Customers are advised to contact TAOS to obtain the latest product information before placing orders or designing TAOS products into systems. TAOS assumes no responsibility for the use of any products or circuits described in this document or customer product design, conveys no license, either expressed or implied, under any patent or other right, and makes no representation that the circuits are free of patent infringement. TAOS further makes no claim as to the suitability of its products for any particular purpose, nor does TAOS assume any liability arising out of the use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. TEXAS ADVANCED OPTOELECTRONIC SOLUTIONS, INC. PRODUCTS ARE NOT DESIGNED OR INTENDED FOR USE IN CRITICAL APPLICATIONS IN WHICH THE FAILURE OR MALFUNCTION OF THE TAOS PRODUCT MAY RESULT IN PERSONAL INJURY OR DEATH. USE OF TAOS PRODUCTS IN LIFE SUPPORT SYSTEMS IS EXPRESSLY UNAUTHORIZED AND ANY SUCH USE BY A CUSTOMER IS COMPLETELY AT THE CUSTOMER’S RISK.

  LUMENOLOGY, TAOS, the TAOS logo, and Texas Advanced Optoelectronic Solutions are registered trademarks of Texas Advanced Optoelectronic Solutions Incorporated.

  Copyright E 2009, TAOS Inc.

  The LUMENOLOGY r Company

  r