Remote Control Doorlock System.

REMOTE CONTROL DOORLOCK SYSTEM

MOHD FAIZAL BIN MUHAMMAD ZAINI

This report is submitted in partial fulfillment of the requirements for the award of Bachelor of Electronic Engineering (Industrial Electronics) With Honours

Faculty of Electronic and Computer Engineering Universiti Teknikal Malaysia Melaka

ii

UNIVERSTI TEKNIKAL MALAYSIA MELAKA

FAKULTI KEJURUTERAAN ELEKTRONIK DAN KEJURUTERAAN KOMPUTER

BORANG PENGESAHAN STATUS LAPORAN PROJEK SARJANA MUDA II

Tajuk Projek : ………

Sesi

Pengajian : ………

Saya ……….. (HURUF BESAR)

mengaku membenarkan Laporan Projek Sarjana Muda ini disimpan di Perpustakaan dengan syarat-syarat kegunaan seperti berikut:

1. Laporan adalah hakmilik Universiti Teknikal Malaysia Melaka.

2. Perpustakaan dibenarkan membuat salinan untuk tujuan pengajian sahaja.

3. Perpustakaan dibenarkan membuat salinan laporan ini sebagai bahan pertukaran antara institusi pengajian tinggi.

4. Sila tandakan ( √ ) :

SULIT* (Mengandungi maklumat yang berdarjah keselamatan atau kepentingan Malaysia seperti yang termaktub di dalam AKTA RAHSIA RASMI 1972)

TERHAD* (Mengandungi maklumat terhad yang telah ditentukan oleh _{organisasi/badan di mana penyelidikan dijalankan)}

TIDAK TERHAD

Disahkan oleh:

__________________________ ___________________________________

(TANDATANGAN PENULIS) (COP DAN TANDATANGAN PENYELIA)

Alamat Tetap: ………...

………...

Tarikh: ……….. Tarikh: ………..

REMOTE CONTROL DOORLOCK SYSTEM 2009/10

MOHD FAIZAL BIN MUHAMMAD ZAINI

BATU 18 ½ KAMPUNG SIALANG 84900, TANGKAK, JOHOR.

√

iii

“I hereby declare that this report is the result of my own work except for quotes as cited in the references.”

Signature : ………..…..…..……….... Author : MOHD FAIZAL BIN MUHAMMAD ZAINI

iv

“I hereby declare that I have read this report and in my opinion this report is sufficient in terms of the scope and quality for the award of Bachelor of Electronic Engineering

(Industrial Electronics) With Honours.”

Signature : ……….

Supervisor’s Name : PN. AZDIANA MD. YUSOP Date : ……….

v

vi

ACKNOWLEDGEMENT

Alhamdulillah, thanks to Allah for His divinity and blessing, I have completed my final year project for courses Bachelor of Electronic Engineering (Industrial Electronics) successfully. I would like to thanks to my lovely family for their encouragement and support. I also would like to thank my supervisors, Pn Azdiana Binti Md Yusop, whose patience, support and help guided me in my work. Thanks also to the people that has helped me along the course of finishing this project. Thank you all.

vii

ABSTRACT

Remote control system is widely used now in the equipment such as television, radio and are one more example used in trasports system as a keylock system. Remote control system is divided to two categories; device based and activity based. Door is a portable obstacle that can be opened up and closed. The combination between tool of system remote control and door will produce one security system. This project will focused the design of the safety system for house especially house door. This sytem is constitute from the extension of remote control device to main system as a signal receipient from it and activate or deactivate the keylock system at the door. The objective of this design is to invent the keylock system that easy to used and easy to maintain. This system also designed to give facilitate for disabled people to use the door. Besides that this inventation also focusing for commercialization. So the inventation of this project will be considering budget expenditure of the component and raw material that will be used to produce one product that can be commercialized.

viii

ABSTRAK

Sistem alat kawalan jauh merupakan sistem yang meluas digunakan pada kebanyakan alat kawalan jauh digunakan pada alat elektrik seperti televisyen, radio, dan pada sistem kenderaan sebagai sistem pengunci keselamatan. Alat kawalan jauh terbahagi kepada 2 iaitu berasaskan peranti dan juga berasaskan aktiviti. Pintu pula merupakan halangan mudah alih yang boleh dibuka atau ditutup. Gabungan antara sistem alat kawalan jauh dan pintu akan menghasilkan satu sistem keselamatan. Projek yang dihasilkan ini sebenarnya menumpukan kepada rekaan satu sistem keselamatan pada pintu rumah. Sistem ini terdiri daripada sambungan alat kawalan jauh kepada sistem utama sebagai penerima isyarat daripada alat kawalan jauh dan mengaktifkan atau mematikan sistem pengunci pada pintu. Matlamat rekaan sistem keselamatan ini adalah untuk mereka cipta sistem pengunci rumah yang mudah digunakan dan diselenggarakan. Sistem ini juga direka untuk memudahkan golongan kurang upaya menggunakan pintu. Selain itu, rekaan ini juga mensasarkan satu matlamat untuk dikomersialkan. Jadi, projek ini direka dengan sebaik mungkin dengan mengambil kira bajet perbelanjaan komponen dan bahan mentah yang digunakan untuk menghasilkan satu produk yang boleh dikomersialkan.

ix

TABLE OF CONTENTS

CHAPTER TITLE PAGE

PROJECT TITLE i

REPORT STATUS VERIFICATION FORM ii

STUDENT’S DECLARATION iii

SUPERVISOR’S DECLARATION iv

DEDICATION v

ACKNOWLEDGEMENT vi

ABSTRACT vii

ABSTRAK viii

TABLE OF CONTENTS ix

LIST OF TABLE xiv

LIST OF FIGURES xv

I INTRODUCTION

1.1 Overview 1

1.2 Project Objective 2

1.3 Problem Statement 2

1.4 Project Scope 4

1.5 Methodology 5

x

II LITERATURE REVIEW

2.1 Remote Keyless Entry System 7

2.1.1 Requirement of Remote Keyless 8 Entry (RKE) System

2.1.2 Detailed RKE Description and 8 Design Objectives

2.1.3 Carrier Generation 10

2.1.4 Power Conservation 11

2.1.5 Infrared Remote Control Process 13

2.2 Type of Remote Control 15

2.2.1 Browser-Based Remote Sessions 16 2.2.2 Software-Based Remote Control 17

2.3 Central Lock 19

2.4 Pneumatic Actuator 20

2.4.1 Comparison of Pneumatic Actuator 27 and Hydraulic Actuator

2.4.2 Advantages of pneumatics 27

2.4.3 Advantages of hydraulics 27

2.5 Transmitter 28

2.6 Receiver 28

2.7 Power Supply 29

2.7.1 Power supply types 29

2.7.2 Direct Current (DC) Power Supply 30 2.7.3 Alternating Current (AC) Power Supply 32

xi

III RESEARCH METHODOLOGY

3.1 The Factors which Influence the Design 35

3.2 Flow Chart of Idea 36

3.3 Method and Approach of Remote Control 38 Doorlock System

IV SIMULATION RESULT AND DISCUSSION

4.1 Simulation Result 41

4.1.1 Diagram for the Whole System 41

4.1.2 Simulation of the System 43

4.2 Discussion 52

V HARDWARE INTERFACING

5.1 Introduction of Hardware Interfacing 54

5.2 Hardware Installation 57

5.2.1 Material Selection 57

5.3 Development Step of the Hardware 59

5.3.1 Measurement and Marking 60

5.3.2 Cutting 60

5.3.3 Welding 61

5.3.4 Installation 61

5.3.5 Testing 63

5.3.6 Finishing 64

xii

5.5 The Component Used in this System 67

5.5.1 Door Knob 67

5.5.2 Central Lock 68

5.5.3 Remote Sensor 70

5.5.4 Solenoid Valve (Actuator) 70

5.5.5 Remote Control 71

5.5.6 Micro Switch 71

5.5.7 Power Supply 72

5.5.8 Wires and Connector 72

5.5.9 Pilot Lamp 73

5.5.10 Buzzer 73

VI PROJECT ANALYSIS

6.1 Project Outcome 74

6.2 Project Analysis 75

6.2.1 Electronic Part Problem 75

6.2.2 Electrical Part Problem 75

6.3 Testing Process 76

6.4 Cost Analysis 76

6.4.1 Raw Material Cost 77

6.4.2 Tool and component cost 78

6.4.3 Overall Cost 80

6.4.4 Profit 80

xiii VII CONCLUSION AND RECOMMENDATION

7.1 Conclusion 81

7.2 Recommendation 83

REFERENCES 84

APPENDIX A 86

APPENDIX B 87

xiv

LIST OF TABLE

NO TITLE PAGE

6.1 Raw material cost 77

6.2 Basic component and tool cost 78

xv

LIST OF FIGURES

NO TITLE PAGE

2.1 An RKE system consists of a keyfob circuit (lower diagram) 9 Transmitting to a receiver (upper diagram).

2.2 To monitor key fob transmissions, an RKE receiver must 12 allocate time to wake

2.3 Diagram of infrared receiver and the flow of the signal data 14 through each process block.

2.4 Transmit signal (carrier frequency = fo) 14

2.5 Data transmission rate 15

2.6 The variation of remote control 16

2.7 Operation diagram of a single acting cylinder 22

2.8 Operation diagram of a double acting cylinder 22

2.9 Pneumatic Cylinder 23

2.10 Schematic symbol for pneumatic cylinder with spring return. 23 2.11 The solenoid valve (actuator) used in the project 24 2.12 A direct pneumatic actuator for converting pressure signal into 25

mechanical shaft motion

2.13 A reverse acting pneumatic actuator 26

2.14 Steady DC from a battery or regulated power supply, 30 this is ideal for electronic circuits

2.15 Smooth DC from a smoothed power supply, this is suitable 31 for some electronics.

2.16 Varying DC from a power supply without smoothing, 31 this is not suitable for electronics.

xvi 2.17 Alternating Current (AC) signal from a power supply 33 this shape is called a sine wave.

2.18 This triangular signal is AC because it changes between 33 positive (+) and negative (-).

3.1 Flowchart of idea 36

3.2 Flow of project 37

3.3 The part of a car alarm 39

4.1 Wiring diagram for the whole system 42

4.2 Planning idea for the system connection 42

4.3 System connection 43

4.4 Schematic diagram of transmitter circuit 44

4.5 The waveform at oscilloscope 1 45

4.6 The waveform at oscilloscope 2 46

4.7 The final waveform at oscilloscope 3 47

4.8 Schematic diagram for the combination of the transmitter and 48 receiver circuit.

4.9 the input waveform from the transmitter. 49

4.10 The expected square wave waveform produced in receiver circuit. 50

4.11 The central lock circuit 51

5.1 Experimental setup of doorlock system 54

5.2 Model of the door 55

5.3 The dimensional model of the door 56

5.4 Flowchart of project (model) impementation 59

5.5 Site and frame produced 61

5.6 the Installation of component 62

5.7 Testing to the model 63

5.8 The iron frame after painted 64

5.9 The door after the wood layer is painted 64

5.10 The inside view 65

5.11 The outside view 65

xvii

5.13 The door knob 67

5.14 The interior door knob that has been modified 67

5.15 Central lock 68

5.16 Remote sensor 70

5.17 The modified solenoid valve with door knob 70

5.18 Remote control device 71

5.19 Micro Switch 71

5.20 Car battery 72

5.21 Wire and connector 72

5.22 Pilot lamp 73

CHAPTER I

INTRODUCTION

1.1 Overview

A remote control deadbolt lock was designed for quadriplegics. The system consists of a modified standard household deadbolt lock, a central lock and a remote control. People who have limited use and control of their hands would use this system to simplify the complicated procedure of using a key to lock and unlock their homes at the touch of a button. The purpose of this project was to simplify the tasks of locking and unlocking a conventional door for people who use wheelchairs and have limited use of their hands and arms. By incorporating the use of a remote control, the inconvenience of using a key was eliminated. With just a push of a button, the locking mechanism in the door can be activated or deactivated. There are several door-locking systems that do not use a conventional key. There is a “credit card” type used in many hotels and the push-button combination lock used in many businesses. Both of these and similar systems did not address the inability of our client to grasp the card key or push the tiny buttons. There are also variations of remote controlled doors and gates, but these tend to be large and expensive systems more suitable for industrial use.

2 1.2 Project Objective

The objectives of this project are:

To design a remote control doorlock system for user to lock and unlock a conventional door.

To commercialize this product to people.

1.3 Problem Statement

The problem statement of this project is divided into several aspects. In remote control doorlock system, the construction of circuit for remote control is one of the important aspects. In remote control system, it is divided into two part; transmitter circuit and receiver circuit. If either one or both circuit is not function, the full system would not work well. The central lock system is the main connector which connecting the remote sensor to solenoid valve (actuator) and alarm indicator. If the central lock is not developed, the system is not fully complete. So, the circuit must be constructed first in electronic software. For my final project, the circuits are developed and simulated by using Multisim, Proteus 7 Professional. From this software, the specification of the circuits can be determined easily. For the design of the door and wiring diagram, the Autocad software will be used to develop its.

3 In the remote control, there has a transmitter which send the data to the main system which placed at the door. That main system consist a central lock which has a receiver that will receive the sent data from the transmitter. The main system can not directly switch on the system (opened up the door) because the main system needs to connected and work together with the actuator to pull and push the lock door. In this project, the two pneumatic actuators are used to work together with the main system. The actuator consist a valve inside which require little pressure to operate and usually double or triple the input force. The actuator is an electric motor drive. The electric motor drive can have a speed-reducing transmission as may be desirable or required. When the actuator is applying in between the system, it can create the great force to pull and push the dead bolt easily.

Beside that, the arrangement of the complete wiring is important aspect need to be focused in order to create the complete and safety locking system for the door. For this aspect, the system needs something to keep the complete wiring. So, a piece of Perspex is used to keep the all wiring set and the main system from anything that can make a short circuit and disturbance in this system. The safety value which has in this system can make it user friendly system whereas people can use it easily.

4 1.4 Project Scope

The scopes of this project are:

Study about the locking mechanism.

Study and research about the usage of remote control system.

Study on the system that will be linked between remote control and the mechanical locking system of the door.

Simulate and investigate the additional circuit in order to apply remote control doorlock system.

Apply the electrical wiring technique to doorlock system, testing and troubleshooting.

5 1.5 Methodology

Generate the simulation model with the system Study the basic concept of

remote control system

Study about the central lock that play role as a main

system connector.

Understand the useful of DC and AC power supply

Simulation result

Make the simulation using Multisim

Analyze the simulation and do problem discussion

Experimental testing Troubleshooting Finish OK OK Not OK Not OK

6 1.6 Thesis Outline

This thesis describes the remote control doorlock system and how to develop this system. This thesis has seven chapters. The first chapter will be describe about a brief introduction about the project consist the overview, objective, problem statement and scope of the project. A literature review of recent work on theory for the device and concept involved and application is presented in chapter 2. Chapter 3 describe about explanation about equipment, component, procedure, rule and technique applies in developing this project. The simulation result, design and discussion about the system will be showed and discussed in chapter 4. Chapter 5 introduce detailed about hardware interfacing between hardware and simulation. And finally, chapter 6 summarizes the contributions of this work along with suggesting avenue for future explorations.

CHAPTER II

LITERATURE REVIEW

This chapter consists of some information about remote control system which included the central lock statement and also an overview of the literature that has been published in relation to build the system.

2.1 Remote Keyless Entry System

A remote keyless system is a system designed to remotely permit or deny access to premises or automobiles. This system was invented by mechanical engineer A.B. Makkar. There are several remote keyless entry (RKE) systems on the market, including but not limited to KeeLoq by Microchip, HITAG by Philips, and AVR411 by Atmel. In the case of automobiles a remote keyless system performs the functions of a standard car key without physical contact; power door locks can be locked or unlocked from several feet away or even from inside a building. A remote keyless system can include both a remote keyless entry system (RKE) and a remote keyless ignition system (RKI).

1.2 Project Objective

The objectives of this project are:

To design a remote control doorlock system for user to lock and unlock a conventional door.

To commercialize this product to people.

1.3 Problem Statement

The problem statement of this project is divided into several aspects. In remote control doorlock system, the construction of circuit for remote control is one of the important aspects. In remote control system, it is divided into two part; transmitter circuit and receiver circuit. If either one or both circuit is not function, the full system would not work well. The central lock system is the main connector which connecting the remote sensor to solenoid valve (actuator) and alarm indicator. If the central lock is not developed, the system is not fully complete. So, the circuit must be constructed first in electronic software. For my final project, the circuits are developed and simulated by using Multisim, Proteus 7 Professional. From this software, the specification of the circuits can be determined easily. For the design of the door and wiring diagram, the Autocad software will be used to develop its.

In the remote control, there has a transmitter which send the data to the main system which placed at the door. That main system consist a central lock which has a receiver that will receive the sent data from the transmitter. The main system can not directly switch on the system (opened up the door) because the main system needs to connected and work together with the actuator to pull and push the lock door. In this project, the two pneumatic actuators are used to work together with the main system. The actuator consist a valve inside which require little pressure to operate and usually double or triple the input force. The actuator is an electric motor drive. The electric motor drive can have a speed-reducing transmission as may be desirable or required. When the actuator is applying in between the system, it can create the great force to pull and push the dead bolt easily.

Beside that, the arrangement of the complete wiring is important aspect need to be focused in order to create the complete and safety locking system for the door. For this aspect, the system needs something to keep the complete wiring. So, a piece of Perspex is used to keep the all wiring set and the main system from anything that can make a short circuit and disturbance in this system. The safety value which has in this system can make it user friendly system whereas people can use it easily.

1.4 Project Scope

The scopes of this project are:

Study about the locking mechanism.

Study and research about the usage of remote control system.

Study on the system that will be linked between remote control and the mechanical locking system of the door.

Simulate and investigate the additional circuit in order to apply remote control doorlock system.

Apply the electrical wiring technique to doorlock system, testing and troubleshooting.

1.5 Methodology

Generate the simulation model with the system Study the basic concept of

remote control system

Study about the central lock that play role as a main

system connector.

Understand the useful of DC and AC power supply

Simulation result

Make the simulation using Multisim

Analyze the simulation and do problem discussion

Experimental testing Troubleshooting Finish OK OK Not OK Not OK

1.6 Thesis Outline

This thesis describes the remote control doorlock system and how to develop this system. This thesis has seven chapters. The first chapter will be describe about a brief introduction about the project consist the overview, objective, problem statement and scope of the project. A literature review of recent work on theory for the device and concept involved and application is presented in chapter 2. Chapter 3 describe about explanation about equipment, component, procedure, rule and technique applies in developing this project. The simulation result, design and discussion about the system will be showed and discussed in chapter 4. Chapter 5 introduce detailed about hardware interfacing between hardware and simulation. And finally, chapter 6 summarizes the contributions of this work along with suggesting avenue for future explorations.

CHAPTER II

LITERATURE REVIEW

This chapter consists of some information about remote control system which included the central lock statement and also an overview of the literature that has been published in relation to build the system.

2.1 Remote Keyless Entry System

A remote keyless system is a system designed to remotely permit or deny access to premises or automobiles. This system was invented by mechanical engineer A.B. Makkar. There are several remote keyless entry (RKE) systems on the market, including but not limited to KeeLoq by Microchip, HITAG by Philips, and AVR411 by Atmel. In the case of automobiles a remote keyless system performs the functions of a standard car key without physical contact; power door locks can be locked or unlocked from several feet away or even from inside a building. A remote keyless system can include both a remote keyless entry system (RKE) and a remote keyless ignition system (RKI).