Development of database for checking fixtures for automotive parts.

(1)

UNIVERSITI TEKNIKAL MALAYSIA MELAKA

DEVELOPMENT OF DATABASE FOR CHECKING FIXTURES

FOR AUTOMOTIVE PARTS

This report submitted in accordance with requirement of Universiti Teknikal Malaysia Melaka (UTeM) for Bachelor Degree of Manufacturing Engineering

(Manufacturing Design) (Hons.)

SHAHRUL IMRAN BIN ZULKIFLI B051010136

880302-26-5441

FACULTY OF MANUFACTURING ENGINEERING 2014

(2)

UNIVERSITI TEKNIKAL MALAYSIA MELAKA

BORANG PENGESAHAN STATUS LAPORAN PROJEK SARJANA MUDA

TAJUK: Development of Database for Checking Fixtures for Automotive Parts

SESI PENGAJIAN: 2013/14 Semester 2

Saya SHAHRUL IMRAN BIN ZULKIFLI

mengaku membenarkan Laporan PSM ini disimpan di Perpustakaan Universiti Teknikal Malaysia Melaka (UTeM) dengan syarat-syarat kegunaan seperti berikut: 1. Laporan PSM adalah hak milik Universiti Teknikal Malaysia Melaka dan penulis. 2. Perpustakaan Universiti Teknikal Malaysia Melaka dibenarkan membuat salinan

untuk tujuan pengajian sahaja dengan izin penulis.

3. Perpustakaan dibenarkan membuat salinan laporan PSM ini sebagai bahan pertukaran antara institusi pengajian tinggi.

4. **Sila tandakan ( )

SULIT

TERHAD

TIDAK TERHAD

(Mengandungi maklumat yang berdarjah keselamatan atau kepentingan Malaysia sebagaimana yang termaktub dalam AKTA RAHSIA RASMI 1972)

(Mengandungi maklumat TERHAD yang telah ditentukan oleh organisasi/badan di mana penyelidikan dijalankan)

Alamat Tetap:

2934-H Taman Muhibbah Jalan Sultanah Bahiyah 05350 Alor Setar, Kedah

Tarikh: ________________________

Disahkan oleh:

Cop Rasmi:

(3)

FAKULTI KEJURUTERAAN PEMBUATAN

Tel : +606 331 6019 | Faks : +606 331 6431/6411

Rujukan Kami (Our Ref) :

Rujukan Tuan (Your Ref) :

23 Jun 2014

Pustakawan

Perpustakaan UTeM

Universiti Teknikal Malaysia Melaka Hang Tuah Jaya,

76100 Durian Tunggal, Melaka.

Tuan/Puan,

PENGKELASAN LAPORAN PSM SEBAGAI SULIT/TERHAD LAPORAN PROJEK SARJANA MUDA KEJURUTERAAN PEMBUATAN (MANUFACTURING DESIGN): SHAHRUL IMRAN BIN ZULKIFLI

Sukacita dimaklumkan bahawa Laporan PSM yang tersebut di atas bertajuk “Development of Database for Checking Fixtures for Automotive Parts” mohon dikelaskan sebagai *SULIT / TERHAD untuk tempoh LIMA (5) tahun dari tarikh surat ini.

2. Hal ini adalah kerana IANYA MERUPAKAN PROJEK YANG DITAJA OLEH

SYARIKAT LUAR DAN HASIL KAJIANNYA ADALAH SULIT.

Sekian dimaklumkan. Terima kasih.

Yang benar,

________________

* Potong yang tidak berkenaan

NOTA: BORANG INI HANYA DIISI JIKA DIKLASIFIKASIKAN SEBAGAI SULIT DAN TERHAD. JIKA LAPORAN DIKELASKAN SEBAGAI TIDAK TERHAD, MAKA

(4)

DECLARATION

I hereby, declared this report entitled “Development of Database for Checking Fixtures for Automotive Parts” is the results of my own research except as cited in references.

Signature : ………

Author’s Name : SHAHRUL IMRAN BIN ZULKIFLI

(5)

APPROVAL

This report is submitted to the Faculty of Manufacturing Engineering of UTeM as a partial fulfillment of the requirement for the degree of Bachelor of Manufacturing Engineering (Manufacturing Design) (Hons.). The member of the supervisory committee is as follow:

………..

(6)

ABSTRAK

Tujuan kajian ini adalah untuk membangunkan pangkalan data untuk Semakan Jadual untuk Bahagian Automotif. Bahagian-bahagian yang digunakan dalam proses semakan seperti “clamper”, “stand” dan “toggle”. Matlamat projek ini adalah untuk melaksanakan pangkalan data memeriksa lekapan bahagian. Projek bermula ialah mengenal pasti masalah semasa yang dihadapi oleh pereka bentuk di jabatan reka bentuk. Masa terbuang telah menjadi masalah utama yang telah pereka untuk dihadapi. Semua data dan maklumat yang berkaitan dengan projek ini telah dicari dan direkodkan dalam kajian literatur. Perisian Catia digunakan sebagai perisian CAD untuk membina model tiga dimensi untuk reka bentuk bahagian-bahagian semua bahagian di perpustakaan bahagian-bahagian yang. Semua bahagian-bahagian yang dianjurkan dalam tiga saiz yang berbeza yang ditentukan oleh saiz panel badan kereta. Merujuk kepada keputusan itu, perpustakaan baru terbentuk atau dibangunkan dengan menggunakan perisian Catia untuk membantu pereka dalam proses reka bentuk lekapan pemeriksaan. Pengesahan perpustakaan telah dijalankan dengan syarikat itu untuk menguji keberkesanan, kebolehgunaan dan kesesuaian. Oleh itu, dengan alat ini dan kaedah telah mempercepatkan lekapan proses reka bentuk memeriksa untuk menjadi lebih cepat dan cekap.

(7)

ABSTRACT

The purpose of this study is to develop database for Checking Fixtures for Automotive Parts. The parts that used in the checking fixture process such as clamper, stand and toggle. The goal of this project is to implement a database of checking fixtures parts. The project started is identify the current problem that faced by the designer at design department. Idle time has been the major problem that designer have to faced. All the data and information related to this project has been sought and recorded in the literature review. Catia software is used as CAD software to construct three-dimensional models for the design of the parts all the parts in the parts library. All the parts are organized in three different sizes which are determined by the size of car body panel. Referring to the result, new libraries are formed or develop using the Catia software to aid the designers in the checking fixture design process. The validation of the library has been conducted with the company to test the effectiveness, usability and relevancy. Therefore, with this tool and method have accelerate the checking fixtures design process to become more quickly and efficient.

(8)

DEDICATION

To my beloved family, my respectful supervisor and examiner, my fellow friends and all the parties involved, thank you so much.

(9)

ACKNOWLEDGEMNET

First and foremost, gratefully wishes to the Almighty, ALLAH S.W.T for all His blessing.

This opportunity has been taken to express sincere appreciation and gratitude to respective supervisor, Mr. Zulkeflee bin Abdullah, for constructive guidance, consistent encouragement, and fulfilling aspiration in completing this project. Also for my supervisor at Shazu Engineering Sdn.Bhd for her kindness, patients, and supporting, I wish her thanks a lot.

Also this chance has been taken to wish thank to the entire workers at the Shazu Engineering for took valuable time to teach and give a proper tutoring to understand about the checking fixtures and teach something that very useful in manufacturing design.

This opportunity absolutely taken to wish special thanks for several people especially all the family members for supporting physically and spiritually throughout in completing this project. Finally, thank wishes to all friends that give me a support and for a sharing an idea during the completion this final year report.

(10)

TABLE OF CONTENT

Abstrak i

Abstract ii

Dedication iii

Acknowledgement iv

Table of Content v

List of Table viii

List of Figure x

List of Abbreviations and Acronyms xiv

CHAPTER 1

1

1.1 Background of the Study 1

1.2 Problem Statement 3

1.3 Objective of the Study 4

1.4 Scope of the Research 4

1.5 Potential Benefits from the Research 5

1.5.1 Benefits to Industry 5

1.5.2 Benefits to University 5

CHAPTER 2

6

(11)

2.2.1 The fixture Design 9

2.2.2 Part Prints 10

2.2.3 Fixture Drawing 11

2.2.4 Frame/Base 12

2.2.5 Locator 13

2.2.6 Clamps 14

2.2.7 Bushings 19

2.2.8 Brackets 20

2.2.9 Fastener 21

2.3 Automotive Body in White 22

2.4 Checking Fixture 24

2.4.1 Stationary Checking Fixtures 25

2.5 Definition of Design 26

2.6 Design Research 27

2.7 Industrial Design 28

2.8 Development Lead Time 29

2.9 Productivity in Automotive 31

CHAPTER 3

33

3.1 Plan and Activities 33

3.2 Design of Research 35

3.3 Background of the Research Location 35

3.4 Research Methodology 36

(12)

3.5.1 Problems Identification 39

3.5.2 Design Concept 42

3.5.3 Size of Checking Fixtures 45

3.5.4 Determine Standard Parts of Checking Fixtures 47

3.5.5 Design the Parts using CAD 48

3.5.6 Organize the Drawing File 49

CHAPTER 4

51

4.1 Introduction 51

4.2 Checking Fixtures Design Loose Panel Parts 51

4.2.1 Body Parts (Panel Data) 53

4.3 Checking Fixture Library 87

4.3.1 Workflow Used of the Library Part 88

4.4 Checking Fixture Database Library Validation 97

4.4.1 Validation Method 97

4.4.2 Validation Result 100

CHAPTER 5

101

5.1 Conclusion 101

5.2 Recommendation for Future Work 102

REFERENCES

APPENDIX

(13)

LIST OF TABLE

Table 3.1: Interview Questions 37

Table 4.1: Size of Checking Fixture 54

Table 4.2: Type of Clamp Used 59

Table 4.3: Types of Clamps 60

Table 4.4: L-bracket Size 63

Table 4.5: Dowel Pin 67

Table 4.6: Diamond Pin 67

Table 4.7: Marking Pin 70

Table 4.8: Small Round Pin 73

Table 4.9: Medium Round Pin 74

Table 4.10: Large Round Pin 74

Table 4.11: Small Hinge Pin 75

Table 4.12: Medium Hinge Pin 75

Table 4.13: Large Hinge Pin 76

Table 4.14: Small Bush Diamond 76

(14)

Table 4.17: Small Bush Round and Marking 77

Table 4.18: Medium Bush Round and Marking 78

Table 4.19: Large Bush Round and Marking 78

Table 4.20: Pin Clip and Holder Pin 79

Table 4.21: Caster Wheel Sizes 80

Table 4.22: Types of Cover Riser/Datum 81

Table 4.23: Types of Bolt 82

Table 4.24: Types of Bolt 83

Table 4.25: Types of Knob Lobed 83

Table 4.26: Types of Lifting Eye Bolt 84

Table 4.27: Types of Screw 84

Table 4.28: Type of Name Plate 86

Table 4.28: Design Process Brief (First Trial) 98

(15)

LIST OF FIGURES

Figure 2.1: Fixture Design 9

Figure 2.2: Fixture Drawing 11

Figure 2.3: Base of CF 12

Figure 2.4: Locator 13

Figure 2.5: Clamps 14

Figure 2.6: Horizontal-handle toggle clamps 15

Figure 2.7: Clamped Position 15

Figure 2.8: Vertical Handle Toggle Clamps 16

Figure 2.9: Clamped Position 16

Figure 2.10: Type of Bushing 17

Figure 2.11: Brackets angle 20

Figure 2.12: Example of fastener 21

Figure 2.13: Body in White 22

Figure 2.14: Structural part of BIW 23

Figure 2.15: Checking Fixtures 24

Figure 2.16: Definitions of Major Development Phases 29

(16)

Figure 3.2: Checking Fixture Process 35

Figure 3.3: Framework of Research 38

Figure 3.4: Flow Chart of Approval Checking Fixture Process 40

Figure 3.5: Categories of Idle Time. 41

Figure 3.6: Design Concept 42

Figure 3.7: Example of Panel Setting. 44

Figure 3.8: Example of Small Checking Fixtures 46

Figure 3.9: Example of Medium Checking Fixtures. 46

Figure 3.10: Example of Large Checking Fixtures. 46

Figure 4.1: CF Main Elements 52

Figure 4.2: Front Area of Car Parts 53

Figure 4.3: Example of basic body parts of the car 54

Figure 4.4: Bracket Hvac Unit Lower Panel (Small) 55

Figure 4.5: Rail Roof Panel (Large) 55

Figure 4.6: Front Floor Panel (Large) 55

Figure 4.7: Front Floor Panel (Large) 56

Figure 4.8: Cowl Top Inner Panel (Medium) 56

Figure 4.9: Cowl Top Outer Panel (Medium) 56

(17)

Figure 4.12: Large Base Structure 59

Figure 4.13: Clamper Stand with Toggle Clamps 64

Figure 4.14: Type C 65

Figure 4.15: Type D 65

Figure 4.16: Type E 65

Figure 4.17: Type A 66

Figure 4.18: Type B 66

Figure 4.19: Caster Wheel Types 80

Figure 4.20: CF Part Library Structures 87

Figure 4.21: Step 1 89

Figure 4.22: Step 2 89

Figure 4.23: Step 3 90

Figure 4.24: Step 4 90

Figure 4.25: Step 5 91

Figure 4.26: Step 6 91

Figure 4.27: Step 7 92

Figure 4.28: Clamper Stand with Toggle 92

Figure 4.29: Step 8 93

Figure 4.30: Pin and Bush 93

(18)

Figure 4.33: Step 10 95

(19)

USED ACRONYMS / ABBREVIATIONS

CF - Checking Fixture

BIW - Body in White

PQR - Part Quality Requirement SESB - Shazu Engineering Sdn. Bhd.

(20)

CHAPTER 1 INTRODUCTION

Chapter one describes the overall background of this project research. The scope of this research is focused at Shazu Engineering Sdn. Bhd. The content of this chapter includes background, problem statement, project objectives, scope of project, and potential benefits from the project.

1.1 Background of the Study

This study introduces development of a library or catalogue for Checking Fixtures items like clamper, stand, and toggle to be used in Checking Fixtures process. Shazu Engineering Sdn.Bhd. has been involved in the automotive industry since its establishment in September 2003. The company is owned by 100% Bumiputra and is entrusted to provide the most cost effective, reliable and accurate consultation services to the customers. As of mid-2009, Shazu Engineering has been assigned as quality consultant for the development of Savvy, Satria Neo, Persona, New Saga and Exora. Starting with only four employees, currently Shazu is supported by 27 dedicated

(21)

Established in the year 2003, Shazu Engineering has been an eminent manufacture of Checking Fixtures & Assembly fixture for many companies. Shazu Engineering is engaged in manufacturing custom designed as well as standard specification products. Shazu Engineering qualified workforce is able to ensure complete compliance with their clients’ requirements and specifications.

The fixtures are manufactured from high quality raw material procured from local vendors with extremely reliable reputations to produce high grade Checking Fixtures and Assembly Fixtures.

Auto-body parts include the stamping parts, subassemblies jointed with stamping parts, the auto-body framework and all kind of trims which are formed into complicated surfaces. The quality of covering these parts considerably affects car performance and airproofing. During the manufacturing process, in order to ensure parts quality, it is important to measure parts with checking fixtures which are used to locate and hold the workpiece in 3D space according to measure planning.

Checking fixtures for auto body parts have different types according to measuring planning and parts features. The main type of such checking fixtures can be described as follows; measuring fixtures, combined checking fixtures, profile modeling casting checking fixtures, and additional checking fixtures. Correctly selecting the checking fixture type for auto body parts is a first step to design a good checking fixture. In the quality control process of auto-body manufacturing, selecting which type of checking fixture takes into consideration on the features and parameters of the part that would be measured; so the information of the auto body part is important for checking fixtures is not unique since numerous plans are possible. Traditionally, the

selection of a checking fixtures type relies heavily on the designer’s expertise and

experience. Performance evaluation of a checking fixtures type is also very difficult due to high non-linear relationship of the design parameters. Consequently, it is not immediately apparent if a checking fixture type is optimal or near optimal for the given part.

(22)

1.2 Problem Statement

As products and processes are becoming more complex, the decision making involved in product design and manufacturing engineering have to consider many variables. Time Loss is some of the major problem experienced in SESB. By reducing time loss, the production output and profitability to the company will increase besides reduce the cost such as salary for overtime work. Design department preparing the concept based on quality integration mode. From the concept, designer will plan the design checking fixtures based on the customer requirements. Designer needs to design the checking fixtures based on the concept, so it will take time to make it, so as a designer, time consuming and accuracy is very important. When it takes too long time and will cause work to be inefficient. It is important to accurately design a checking fixture. It can be time consuming to change the design if the design is not accurate or design changed by the customers. Checking fixtures has many types of size. It depends on the customers which part of the car that they want to develop such as rear floor, front floor, side door, panel roof and many mores. Checking fixtures have many child parts such as toggle clamp, clamper, and stand. It will take time to design all the parts to make a checking fixtures process done.

(23)

1.3 Objective of the Study

The purpose of this study is to develop database for (CF) Checking Fixtures for automotive parts. The complexity and detail of a database design is dictated by the complexity and size of the checking fixtures itself. Overall, the study objective involves three main stages which are:

i. To identify the problem of time constraints in the design process of Checking Fixtures.

ii. To recommend tools and methods used in Checking Fixture process. iii. To develop a library or catalogue for Checking Fixtures processes parts.

1.4 Scope of the Research

This study seeks to solve the problems as SESB located at Shah Alam, Selangor. SESB is a company that manufactures checking fixtures for cars and listed among the automotive industry. This study will focus primarily on the loose panel part and time loss at the design department. Interview and observation methods also include gaining more understanding about some detail processes. The result of the study will then be used to achieve the objectives. This study was limited only for Shazu Engineering Sdn. Bhd.

(24)

1.5 Potential Benefits from the Research

Following are the potential benefits that can be obtained from the carried out project. The potential benefits from the project had been classified into two categories:

1.5.1 Benefits to Industry

The benefits of the conducted project to the industry can be summaries as below:

a) The manufacturing industry and students can exchange knowledge between each other.

b) Increase the accuracy of designing the important automotive parts. c) The improvements of the work efficiency.

1.5.2 Benefits to University

The benefits of the conducted project to the industry can be summaries as follow:

a) Create the relationship between UTeM and manufacturing industry. b) Providing possible subject to be taught in UTeM that is applicable in real

industry world.

c) The mission of UTeM achieved, which is to develop a curriculum that encourages critical thinking, problem solving, teamwork and social skills.

(1)

USED ACRONYMS / ABBREVIATIONS

CF - Checking Fixture BIW - Body in White

PQR - Part Quality Requirement SESB - Shazu Engineering Sdn. Bhd.

(2)

CHAPTER 1 INTRODUCTION

1.1 Background of the Study

(3)

The fixtures are manufactured from high quality raw material procured from local vendors with extremely reliable reputations to produce high grade Checking Fixtures and Assembly Fixtures.

selection of a checking fixtures type relies heavily on the designer’s expertise and

(4)

1.2 Problem Statement

(5)

1.3 Objective of the Study

i. To identify the problem of time constraints in the design process of Checking Fixtures.

ii. To recommend tools and methods used in Checking Fixture process. iii. To develop a library or catalogue for Checking Fixtures processes parts.

1.4 Scope of the Research

(6)

1.5 Potential Benefits from the Research

Following are the potential benefits that can be obtained from the carried out project. The potential benefits from the project had been classified into two categories:

1.5.1 Benefits to Industry

The benefits of the conducted project to the industry can be summaries as below:

a) The manufacturing industry and students can exchange knowledge between each other.

b) Increase the accuracy of designing the important automotive parts. c) The improvements of the work efficiency.

1.5.2 Benefits to University

The benefits of the conducted project to the industry can be summaries as follow:

a) Create the relationship between UTeM and manufacturing industry. b) Providing possible subject to be taught in UTeM that is applicable in real

industry world.

c) The mission of UTeM achieved, which is to develop a curriculum that encourages critical thinking, problem solving, teamwork and social skills.

Development of database for checking fixtures for automotive parts.

UNIVERSITI TEKNIKAL MALAYSIA MELAKA