Kajian Kriteria Aus Pahat Dan Kondisi Pemotongan Pada Operasi Pembubutan Kering Baja AISI 1045 Yang Dikeraskan Menggunakan Pahat Karbida CVD Berlapis
4. Diharapkan untuk mencari lokasi yang tenang dan tidak adanya getaran
pada lantai pada saat mengukur keausan mata pahat supaya hasil lebih
akurat.
DAFTAR PUSTAKA
Azom,
2004,
AISI
1045
Medium
Carbon
Steel
From:
http://www.azom.com/article.aspx?ArticleID=6130. 12 Juni 2016
Bh,Varaprasad, 2014, Effect of Machining Parameters on Tool Wear in Hard
Turning of AISI D3 Steel, Procedia Engineering 97 ( 2014 ) 338 – 345.
J.A.Schey, 1987. Introduction to Manfacturing Processes, International Editions.
Mc
Grow-Hill International Editions.
Kalpakjian, S. 1995, Manufacturing Engineering and Technology. Third Edition.
Addison-Wesley Publishing Company.
Kendall, A.L.,2005, Tool Life And Tool Wear, Metals Handbook, 10th Ed.
Machining Processes, ASM International 16, pp.666-677.
Kulkarni, Atul P, Dry turning of AISI 304 Austenitic Stainless Steel Using
AlTiCrN Coated Insert Produced by HPPMS Technique, prcedia
engineering 64, pp 737-746
Lalbondre, Rajshekhar. Krishna, Prasad. C, Mohankumar G, 2013, Machinability
Studies Of Low Alloy Steels By Face Turning Method:An Experimental
Investigation, Procedia Engineering 64, pp. 632-641.
Lim, C.Y.H., Lau,P.P.P., Lim,S.C., 2001, the effects of work material on tool
wear, Wear 250, pp. 334-348.
Narasimhulu, A, 2012, Dry Machining of Ti-6Al-4V using PVD Coated, TiAlN Tools ,
Proceedings of the World Congress on Engineering 2012 Vol III
Universitas Sumatera Utara
Nordgren, A, 2014, Experimental study and modeling of plastic deformation of
cemented carbide tools in turning, Procedia CIRP 14, pp 599-604
Rochim, Taufiq. 1993, Teori dan Teknologi Proses Pemesinan, Bandung :
Penerbit ITB.
Srithar, A, 2014, Experimental Investigation and Surface Roughness Analysis on
Hard turning of AISI D2 Steel Using Coated Carbide Insert, Procedia
Engineering 97, pp 72-77
S, Swapnagandha, 2013, Machinability studies of austenitic stainless steel (AISI
304) using PVD cathodic arc evaporation (CAE) system deposited
AlCrN/ TiAlN coated carbide inserts, Procedia Engineering 64, pp 907914.
Universitas Sumatera Utara
pada lantai pada saat mengukur keausan mata pahat supaya hasil lebih
akurat.
DAFTAR PUSTAKA
Azom,
2004,
AISI
1045
Medium
Carbon
Steel
From:
http://www.azom.com/article.aspx?ArticleID=6130. 12 Juni 2016
Bh,Varaprasad, 2014, Effect of Machining Parameters on Tool Wear in Hard
Turning of AISI D3 Steel, Procedia Engineering 97 ( 2014 ) 338 – 345.
J.A.Schey, 1987. Introduction to Manfacturing Processes, International Editions.
Mc
Grow-Hill International Editions.
Kalpakjian, S. 1995, Manufacturing Engineering and Technology. Third Edition.
Addison-Wesley Publishing Company.
Kendall, A.L.,2005, Tool Life And Tool Wear, Metals Handbook, 10th Ed.
Machining Processes, ASM International 16, pp.666-677.
Kulkarni, Atul P, Dry turning of AISI 304 Austenitic Stainless Steel Using
AlTiCrN Coated Insert Produced by HPPMS Technique, prcedia
engineering 64, pp 737-746
Lalbondre, Rajshekhar. Krishna, Prasad. C, Mohankumar G, 2013, Machinability
Studies Of Low Alloy Steels By Face Turning Method:An Experimental
Investigation, Procedia Engineering 64, pp. 632-641.
Lim, C.Y.H., Lau,P.P.P., Lim,S.C., 2001, the effects of work material on tool
wear, Wear 250, pp. 334-348.
Narasimhulu, A, 2012, Dry Machining of Ti-6Al-4V using PVD Coated, TiAlN Tools ,
Proceedings of the World Congress on Engineering 2012 Vol III
Universitas Sumatera Utara
Nordgren, A, 2014, Experimental study and modeling of plastic deformation of
cemented carbide tools in turning, Procedia CIRP 14, pp 599-604
Rochim, Taufiq. 1993, Teori dan Teknologi Proses Pemesinan, Bandung :
Penerbit ITB.
Srithar, A, 2014, Experimental Investigation and Surface Roughness Analysis on
Hard turning of AISI D2 Steel Using Coated Carbide Insert, Procedia
Engineering 97, pp 72-77
S, Swapnagandha, 2013, Machinability studies of austenitic stainless steel (AISI
304) using PVD cathodic arc evaporation (CAE) system deposited
AlCrN/ TiAlN coated carbide inserts, Procedia Engineering 64, pp 907914.
Universitas Sumatera Utara