Produktivitas Permesinan Keras Bahan Baja Dengan Pahat Cvd Karbida Berlapis : Studi Kasus Pada Produksi Shaft Thresher
3. Teliti dalam memasukan NC program pada mesin agar terhindar dari
kesalahan seperti salah penentuan titik 0,0 yang dapat menyebabkan
tabrakan antara rumah pahat dengan benda kerja
4. Memperhatikan panjang pemesinan setelah passing agar mata pahat
tidak pecah guna tidak mengulangi penelitian.
5. Lakukan kalibrasi alat ukur Surface Roughness Tester Mitotoyo
terlebih dahulu sebelum penelitian agar dicapai pengukuran yang
tepat.
DAFTAR PUSTAKA
1. A. P. Kene, KashfullOrra. “Experimental Investigation of Tool Wear
Behavior of Multi-Layered Coated Carbide Insert Using Various Sensors
in Hard Turning”
2. A. Srithar, K. Palanikumar, B. Durgaprased, “Experimental Investigation
and Surface Roughness Analysis on Hard Turning of AISI D2 Steel Using
Coated Carbide Insert”.
3. Bh, Varaprasad, 2014, “Effect of Machining Parameters on Tool Wear in
Hard Turning of AISI D3 Steel” Procedia Engineering 97 (2014) 338-345
4. D.M. D’Addona, Sunil. J. Raykar, “Analysis of Surface Roughness in
Hard Turning Using Wiper Insert Geometry” Procedia Engineering 99
(2015) 243-276
5. E. Uhlman, B.Stawiszynksi, C.Leyens, S.Heinze, F.Sammler. “Hard
Turning of Hot Work and Cold Steel WithHiPMS and DCMS TiAIN
Coated Carbide Insert”
6. J.A.Schey, 1987, Introduction to Manufacturing Processes, International
Edition. Mc Grow-Hill International Editions.
Universitas Sumatera Utara
7. J. Guddat, R.M’Saoubi, P. Alm, D. Meyer, “Hard Turning of AISI 52100
Using PCBN Wiper Geometry Inserts and The Resulting Surface Integrity”
8. Kendall, A.L., 2005, Tool Life and Tool Wear, Metal Handbook, 10�ℎ Ed.
Machining Processes, ASM Intenational 16, pp.666-677
9. Rochim Taufiq, 1993, “Proses Permesinan”, Erlangga, Jakarta. Bandung,
Penerbit ITB
10. R.S Khurmi and JK Gupta, 2005 “A Textbook of Machine Design”
11. R.Suresh, S. Basavarajappa, G.L. Samuel “Predective Modeling of Cutting
Forces and Tool Wear in Hard Turning Using Surface Response
Methodology”
12. Serope Kalpakjian
and
Steven
R.
Schimd,
2009, 6th
Edition
“Manufacturing Engineering and Technology”, Publisher : Pearson
Prentice Hall
13. Tool Wear in Hard Turning of AISI D3 Steel “Rahul. G. Chaudhari,
Fukuo. Hashimoto, “Process Controls For Surface Integrity Genereted by
Hard Turning”
Universitas Sumatera Utara
kesalahan seperti salah penentuan titik 0,0 yang dapat menyebabkan
tabrakan antara rumah pahat dengan benda kerja
4. Memperhatikan panjang pemesinan setelah passing agar mata pahat
tidak pecah guna tidak mengulangi penelitian.
5. Lakukan kalibrasi alat ukur Surface Roughness Tester Mitotoyo
terlebih dahulu sebelum penelitian agar dicapai pengukuran yang
tepat.
DAFTAR PUSTAKA
1. A. P. Kene, KashfullOrra. “Experimental Investigation of Tool Wear
Behavior of Multi-Layered Coated Carbide Insert Using Various Sensors
in Hard Turning”
2. A. Srithar, K. Palanikumar, B. Durgaprased, “Experimental Investigation
and Surface Roughness Analysis on Hard Turning of AISI D2 Steel Using
Coated Carbide Insert”.
3. Bh, Varaprasad, 2014, “Effect of Machining Parameters on Tool Wear in
Hard Turning of AISI D3 Steel” Procedia Engineering 97 (2014) 338-345
4. D.M. D’Addona, Sunil. J. Raykar, “Analysis of Surface Roughness in
Hard Turning Using Wiper Insert Geometry” Procedia Engineering 99
(2015) 243-276
5. E. Uhlman, B.Stawiszynksi, C.Leyens, S.Heinze, F.Sammler. “Hard
Turning of Hot Work and Cold Steel WithHiPMS and DCMS TiAIN
Coated Carbide Insert”
6. J.A.Schey, 1987, Introduction to Manufacturing Processes, International
Edition. Mc Grow-Hill International Editions.
Universitas Sumatera Utara
7. J. Guddat, R.M’Saoubi, P. Alm, D. Meyer, “Hard Turning of AISI 52100
Using PCBN Wiper Geometry Inserts and The Resulting Surface Integrity”
8. Kendall, A.L., 2005, Tool Life and Tool Wear, Metal Handbook, 10�ℎ Ed.
Machining Processes, ASM Intenational 16, pp.666-677
9. Rochim Taufiq, 1993, “Proses Permesinan”, Erlangga, Jakarta. Bandung,
Penerbit ITB
10. R.S Khurmi and JK Gupta, 2005 “A Textbook of Machine Design”
11. R.Suresh, S. Basavarajappa, G.L. Samuel “Predective Modeling of Cutting
Forces and Tool Wear in Hard Turning Using Surface Response
Methodology”
12. Serope Kalpakjian
and
Steven
R.
Schimd,
2009, 6th
Edition
“Manufacturing Engineering and Technology”, Publisher : Pearson
Prentice Hall
13. Tool Wear in Hard Turning of AISI D3 Steel “Rahul. G. Chaudhari,
Fukuo. Hashimoto, “Process Controls For Surface Integrity Genereted by
Hard Turning”
Universitas Sumatera Utara