DAFTAR PUSTAKA Analisa Pengaruh Filler Serbuk Zinc Terhadap Sifat Mekanik Sambungan Beda Material Pada Las Titik Antara Baja Tahan Karat Dan Aluminium.

DAFTAR PUSTAKA

Agustriyana, L., Irawan, Y.S., Sugiarto. (2011). Pengaruh Kuat Arus dan
Waktu Pengelasan Pada Proses Las Titik (Spot Welding) Terhadap
Kekuatan Tarik dan Mikrostruktur Hasil Las dari Baja Fasa Ganda
(Ferrite-Martensite), Jurnal Rekayasa Mesin, Vol.2, p. 175-181.
Amstead ,B,H., Djaprie,S (Alih Bahas )1995, Teknologi Mekanik,Jilid I, PT
Erlangga,Jakarta
ANSI/AWS/SAE/D8.9 An American National Standard. 1997.
Recommended Practices for Test Methods for Evaluating the
Resistance Spot Welding Behavior of AutomotiveSheet Steel
Materials, American Welding Society, Miami, p. 33-37.
Aravinthan, A and Nachimani, C. 2011. Analysis of Spot Weld Growth on
Mild and Stainless steel. Supplement To The Welding Journal ,
vol.90, (August 2011). p 143-147.
Arghavani, M. dkk. (2016). Role of zinc layer in resistance spot welding of
aluminium to steel. doi: 10.1016/j.matdes.2016.04.033. Department
of Materials Science and Engineering, Sharif University of
Technology, P.O. Box 11365-9466, Azadi Ave., Tehran, Iran.
ASME BPVC IX, 2010, Boiler & pressure vessel code section IX, welding
and brazing qualification, New York

Atabaki M, dkk. 2013. Welding of aluminum alloys to steels: an overview.
OMB No. 0704-0188.

Chao,Y.,J. 2003. Ultimate Strength and Failure Mechanism of Recistance
Spot Weld Subjectid to Tensile , Shear, or Combined Tensile/Shear
Loads. Jurnal of Enginering Material and Teknologi, Vol.125
Charde, N. (2013). Investigating Spot Weld Growth On 304 Austenitic
Stainless Steel (2 mm). Journal of Engineering Science and
Technology Vol. 8, No. 1 (2013) 69 – 76 Annual Book of ASME IX
Standard, 2001, Qualification Standard for Welding and Brazing
Prosedures, Welder, Brazers, and Welding and Brazing Operations,
p.152-185, The American Society of Mechanical Engineers, New
York..
Deni D,R (2014) Analisis Pengaruh Arus dan Waktu Pengelasan
Terhadap Sifat Mekanik Sambungan Las Titik (Spot Welding) Logam
Tak Sejenis, Teknik Mesin UMS.
Haikal, 2014, “Pengaruh Tegangan Listrik dan Waktu Pengelasan
Terhadap Sifat Fisik dan Mekanik Sambungan Las Titik (Resistance
Spot Welding) Logam Tak Sejenis 3 Lapis 316L,SS400,j1”,Teknik
Mesin UNS

ISF welding and joining institute, 2005, Resistance Spot Welding
Resistance projection welding and resistance seam welding, ISF
aachen welding and joining institute, New Jersey.
Joko Waluyo,2013,Pengaruh Tebal Plat Alumunium Dan Lama
Penekanan Pada Pengelasan Titik Terhadap Sifat Fisis,Mekanik
Dan Efisiensi Panas.Teknik Mesin AKPRIND Yogyakarta.

Kalpakjian,S&Schamid,S.R, 2009. Manufacturing Engineering Tecnologi.
New Jersey: Prentice Hall International
Kenyon, W., 1985., Dasar-Dasar Pengelasan , Terj. Ginting D., Erlangga,
Jakarta, hal 10
Lippold,J.,1996, Structural Stability of Dissimilar Weld Between Two CrMo,V Steels, Supplement to The Welding Jurnal
Marashi, P., Pouranvari, S. Amirabdollahian, A. Abdei, M. Goodarzi, 2008,
Microsructure and failure behavior of dissimilar resistance spot
welds between low carbon galvanized and austenitic stainless steel,
Material Science and Engineering A 480.
Miller,2012, Hand Book For Resistence Spot Welding,Miller Electric,USE.
Pouranvari,M., 2010 Effect of Welding Current on the Mechanical
Response of Resistance Spot Welds of Unequal Thickhness Steel
Sheets in Tensile-Shear Loading Condition, International

Multidisciplinary Science and Engineering,Vol 2,pp.6
Ruukki, 2007, Resistance Spot Welding Manual. Finland: Rataruukki
Corpotation
Salim dan Triyono, 2012, Kekuatan Tarik dan Geser Dengan Pengelasan
Resistance Spot Welding (RSW) Antara Baja Karbon Rendah
Dengan Aluminium. Teknik Mesin UNS.
Surdia. T, dan Saito. S, 2005, Pengetahuan Bahan Teknik, cetakan
keenam, Pradnya pramita, Jakarta

Wiryosumarto, H. dan T. Okumura, 2000, Teknologi Pengelasan Logam,
cetakan kedelapan, Pradnya pramita, Jakarta