Analisa Proses Laju Korosi dan Dampak Yang Dihasilkan Pada Evaporator Sistem Desalinasi Air Laut Keadaan Vakum
ABSTRAK
Korosi adalah proses natural yang mengakibatkan material kehilangan kekuatan
mekanisnya dan berakibat pada deformasi yang menghasilkan kegagalan.
Penelitan ini menganalisa pemakaian bahan logam paduan Stainless Steel Tipe
304 sebagai material pembuatan evaporator sistem desalinasi air laut dalam
kondisi vakum dengan tujuan untuk menganalisa seberapa cepat proses korosi
terjadi, nilai laju korosi dan deformasi yang terjadi pada struktur evaporator.
Penelitian dilakukan dalam dua metode, metode pertama secara eksperimental
untuk mengukur laju korosi evaporator dalam keadaan kerja riil dan metode kedua
secara simulasi untuk menunjukkan deformasi dan laju korosi dengan parameter
input simulasi yang mendekati keadaan kerja eksperimental.Penelitan
mendapatkan hasil laju korosi sebesar 10.12 mm/tahun (398,03 mils/tahun).
Sementara itu, secara simulasi didapati bahwa laju korosi terhadu sebesar 9,636
mm/tahun (379,37 mils/tahun) dengan perbedaan perhitungan ralat sebesar 4.7%
terhadap hasil perhitungan eksperimental. Deformasi berbentuk pit (lubang) pada
permukaan evaporator juga dapat terlihat pada hasil simulasi. Hasil yang dapat
didapatkan dari penelitian menunjukkan bahwa penggunaan logam paduan
Stainless Steel Tipe 304 tidak dapat digunakan sebagai material pembuatan
evaporator dalam sistem desalinasi air laut keadaan vakum.
Kata Kunci : Korosi, Laju Korosi, Desalinasi Air Laut, Dampak Korosi, Stainless
Steel-304, Evaporator.
Universitas Sumatera Utara
ABSTRACT
Corrosion is a natural process that will cause material to lose its mechanical
strength, this will cause a deformation of the material structure which eventually
result to a failure, This research will analyze the usage of Stainless Steel Type304 alloy as main material for an evaporator in a vacuum sea water desalination
system where its goals is to analyze how fast the corrosion process will began, the
value of its corrosion rate, and the deformation of evaporator surface structure.
The experiment was conducted in two method, the first method is done by
experimenting the evaporator in real-time work condition and the second method
is done through a simulation, using an input parameter that resembles the realtime condition. Both process have an objective to measure the evaporator
corrosion rate with structure deformation shown in simulation process. The
research yield a result of 10.12 mm/year (398.03 mils/year). While from
simulation method the corrosion rate yield a result of 9.363 mm/year (379.37
mm/year) with a validation result shown a differences of 4.7% against
experimental method The deformation of the structure is shaped as a pit located
at the evaporator surface. The result of the research concludes that Stainless Steel
Type-304 alloy can’t be used as an evaporator main material in a vacuum sea
water desalination system.
Keywords : Corrosion, Corrosion Rates, Sea Water Desalination System,
Corrosion Effect, Process of Corrosion
Universitas Sumatera Utara
Korosi adalah proses natural yang mengakibatkan material kehilangan kekuatan
mekanisnya dan berakibat pada deformasi yang menghasilkan kegagalan.
Penelitan ini menganalisa pemakaian bahan logam paduan Stainless Steel Tipe
304 sebagai material pembuatan evaporator sistem desalinasi air laut dalam
kondisi vakum dengan tujuan untuk menganalisa seberapa cepat proses korosi
terjadi, nilai laju korosi dan deformasi yang terjadi pada struktur evaporator.
Penelitian dilakukan dalam dua metode, metode pertama secara eksperimental
untuk mengukur laju korosi evaporator dalam keadaan kerja riil dan metode kedua
secara simulasi untuk menunjukkan deformasi dan laju korosi dengan parameter
input simulasi yang mendekati keadaan kerja eksperimental.Penelitan
mendapatkan hasil laju korosi sebesar 10.12 mm/tahun (398,03 mils/tahun).
Sementara itu, secara simulasi didapati bahwa laju korosi terhadu sebesar 9,636
mm/tahun (379,37 mils/tahun) dengan perbedaan perhitungan ralat sebesar 4.7%
terhadap hasil perhitungan eksperimental. Deformasi berbentuk pit (lubang) pada
permukaan evaporator juga dapat terlihat pada hasil simulasi. Hasil yang dapat
didapatkan dari penelitian menunjukkan bahwa penggunaan logam paduan
Stainless Steel Tipe 304 tidak dapat digunakan sebagai material pembuatan
evaporator dalam sistem desalinasi air laut keadaan vakum.
Kata Kunci : Korosi, Laju Korosi, Desalinasi Air Laut, Dampak Korosi, Stainless
Steel-304, Evaporator.
Universitas Sumatera Utara
ABSTRACT
Corrosion is a natural process that will cause material to lose its mechanical
strength, this will cause a deformation of the material structure which eventually
result to a failure, This research will analyze the usage of Stainless Steel Type304 alloy as main material for an evaporator in a vacuum sea water desalination
system where its goals is to analyze how fast the corrosion process will began, the
value of its corrosion rate, and the deformation of evaporator surface structure.
The experiment was conducted in two method, the first method is done by
experimenting the evaporator in real-time work condition and the second method
is done through a simulation, using an input parameter that resembles the realtime condition. Both process have an objective to measure the evaporator
corrosion rate with structure deformation shown in simulation process. The
research yield a result of 10.12 mm/year (398.03 mils/year). While from
simulation method the corrosion rate yield a result of 9.363 mm/year (379.37
mm/year) with a validation result shown a differences of 4.7% against
experimental method The deformation of the structure is shaped as a pit located
at the evaporator surface. The result of the research concludes that Stainless Steel
Type-304 alloy can’t be used as an evaporator main material in a vacuum sea
water desalination system.
Keywords : Corrosion, Corrosion Rates, Sea Water Desalination System,
Corrosion Effect, Process of Corrosion
Universitas Sumatera Utara