DAFTAR ISI
Halaman KATA PENGANTAR
i ABSTRAK
iii ABSTRACT
iv DAFTAR ISI
v DAFTAR TABEL
vii DAFTAR
GAMBAR viii
DAFTAR LAMPIRAN ix
BAB 1 PENDAHULUAN 1
1.1 Latar Belakang 1
1.2 Perumusan Masalah 2
1.3 Batasan
Masalah 3
1.4 Tujuan
Penelitian 3
1.5 Manfaat Penelitian 3
BAB 2 TINJAUAN PUSTAKA 4
2.1 Klasifikasi Logam 4
2.2 Struktur dan Sifat Baja Cor 4
2.2.1 Struktur Coran Baja Karbon 4
2.2.2 Sifat-Sifat Coran Baja Karbon 5
2.3 Struktur dan Sifat-sifat Baja Cor Khusus 6
2.4 Baja Cor Tahan Karat 7
2.4.1 Sruktur dan Sifat-sifat dari Baja Cor Tahan Panas 8
2.4.2 Struktur dan Sifat-sifat dari Baja Cor Pospor P Tinggi 8
2.5 Sifat- Sifat Mekanik Bahan
9 2.5.1 Uji tarik
9 2.5.1 Kuat tarik maksimum
9 2.5.2 Perpanjangan elongation
10 2.5.2 Uji Kekerasan
10 2.5.3 Uji Impact
11 2.5.4 Struktur Mikro
12 BAB
III METODE
PENELITIAN 13
3.1 Lokasi
Penelitian 13
3.2 Bahan
dan Alat 13
3.2.1 Bahan
13 3.2.2
Alat 13
Universitas Sumatera Utara
3.3 Variabel Penelitian 16
3.3.1 Variabel
Tetap 16
3.3.2 Variabel
Berubah 16
3.4 Prosedur Penelitian 16
BAB. IV HASIL DAN PEMBAHASAN 19
4.1 Pembuatan Sampel Uji 19
4.2 Pengujian Tarik 20
4.3 Pengujan Kekerasan 24
4.4 Pengujian Impact 26
4.5 Uji Metalografi 28
BAB. V KESIMPULAN DAN SARAN 33
5.1 Kesimpulan 33
5.2 Saran
33 DAFTAR PUSTAKA
34 LAMPIRAN
Universitas Sumatera Utara
DAFTAR TABEL
No. Judul
Halaman Tabel
4.1 Tabel Data Pengujian Tarik
21 4.2
Tabel Hasil Perhitungan Pengujian Tarik 22
4.3 Tabel Hasil Perhitungan Pengujian Tarik Rata-rata
22 4.4
Tabel Data Pengujian Kekerasan 25
4.5 Tabel Data Pengujian Impact
27
Universitas Sumatera Utara
DAFTAR GAMBAR
No. Gambar
Judul Gambar Halaman
3.1
Presision Catting Machine
14 3.2
Mesin Gerinda
15 3.3
Mesin Poles
15 3.4
Metallurgical microscope
16 3.5 Diagram
Alir Penelitian
18 4.1
Keel Block a Tampak Samping, b Tampak Atas
19 4.2
Sampel uji tarik
20 4.3
Benda Uji Setelah Putus
20 4.4
Grafik Kuat tarik kNmm
2
vs konsentrasi P
23 4.5
Grafik Regangan vs Konsentrasi Pospor
23 4.6
Grafik perpanjangan vs konsentrasi Pospor P
24 4.7
Sampel uji Kekerasan
24 4.8
Kekerasan vs Konsentrasi unsur P
25 4.9
Sampel uji impact 26
4.10
Nilai Impact J mm
2
vs persentase Pospor
27 4.11
Spesimen Uji Metalografi 28
4.12
Gambar Struktur Mikro pada Konsentrasi P 0,02
29 4.13
Gambar Struktur Mikro pada Konsentrasi P 0,03
30 4.14
Gambar Struktur Mikro pada Konsentrasi P 0,04
30 4.15
Gambar Struktur Mikro pada Konsentrasi P 0,05
31 4.16
Gambar Struktur Mikro pada Konsentrasi P 0,06
32
Universitas Sumatera Utara
DAFTAR LAMPIRAN
No. Lampiran
Judul Halaman A
Tabel Carbon Steel Casting JIS G 5101 1975 L-1
B Foto Kegiatan Penelitian
L-2
Universitas Sumatera Utara
PENGARUH KONSENTRASI POSPOR P TERHADAP SIFAT MEKANIK BAJA KARBON RENDAH
ABSTRAK
Telah dilakukan penelitian tentang pengaruh Pospor P terhadap sifat mekanik baja karbon rendah dengan cara memvariasikan presentasi unsur Pospor P. Bahan baku
dengan komposisi SC 37 dilebur pada tanur listrik induksi kemudian presentasi unsur Pospor P divariasikan sebanyak lima variasi, yaitu: v
1
=0,02, v
2
=0,03, v
3
=0,04, v
4
=0,05, dan v
5
=0,06, masing-masing dicor pada cetakan pasir. Sampel yang dihasilkan melalui variasi presentase unsur Pospor P diuji untuk
melihat sifat mekaniknya dilakukan pengujian tarik, kekerasan, impact, dan metalograpi. Data yang diperoleh dari hasil pengujian kemudian dianalisa, sehingga
dapat diketahui pengaruh presentase unsur Pospor P pada baja karbon rendah. Dari hasil pengujian tarik diketahui bahwa kuat tarik paling rendah pada konsentrasi
0,02 adalah 361,91 kNmm
2
dan yang paling berat pada konsentrasi 0,06, yaitu 459,79 kNmm
2
. Untuk uji kekerasan konsentrasi 0,02 adalah 58,7 HRB dan konsentrasi 0,06 adalah 77,3 HRB. Untuk impact konsentrasi 0,02 bernilai
impact 0,2622 joulemm
2
dan konsentrasi 0,06 bernilai impact 0,1869 joulemm
2
. Untuk metalograpi perbesaran 200x yang dietsa dengan Nital 3 pada konsentrasi
0,02 bagian struktur perlit gelap dan struktur ferit terang dan konsentrasi 0,06 jumlah perlit semakin banyak dan ferit sedikit.
Kata kunci: baja karbon rendah, Pospor, sifat mekanik
Universitas Sumatera Utara
THE EFFECT OF PHOSPHORUS P ON MECHANICAL PROPERTIES OF LOW CARBON STEEL
ABSTRACT
Has done research on the influence of phosphorus P on the mechanical properties of low carbon steels by varying the presentation of the element phosphorus P. Raw
materials with the composition of SC 37 is melted in electric induction furnaces and presentation elements phosphorus P was varied as much as five variations, namely:
v = 0.02, v = 0.03, v = 0.04, v = 0.05, and v = 0.06, respectively
1 2
3 4
5
casted in sand molds. Samples are produced through the variation of the percentage of the element phosphorus P tested to see its mechanical properties tensile testing,
hardness, impact, and metalography. Data obtained from the test results were analyzed, so that can know the influence of the percentage of the element phosphorus
P on low carbon steel. From the results of tensile testing is known that the lowest tensile strength at a concentration of 0.02 is 361.91 kNmm and most severe at
2
concentrations of 0.06, is 459.79 kNmm . To test the hardness concentration of
2
0.02 was 58.7 HRB and the concentration of 0.06 was 77.3 HRB. Concentration of 0.02 for the impact value is 0.2622 joulemm and concentration of 0.06 for the
2
impact value is 0.1869 joulemm . To metalography 200x magnification is etched
2
with Nital 3 at a concentration of 0.02 the dark pearlite structure and the structure of ferrite and concentration of 0.06 light the amount of pearlite and
ferrite little more. Key words: low carbon steel, Phosphorus, mechanical properties
Universitas Sumatera Utara
BAB I
PENDAHULUAN
1.1. Latar belakang