Application Machining Once the CeramiGrade Rebuild has Cleaning Health and safety

3.06 314

2. Mixing

Transfer the contents of Base and Activator containers from the respective jars into the mixing container provided. Mix in the raio indicated. Lids should be replaced immediately after use. The two components should be thoroughly mixed until completely streak free and a uniform colour is achieved, using the spatula provided.

3. Application

Prepared Surfaces should be dry. Using the spatula provided the mixed material should be spread evenly onto the prepared area, working the material into any cracks and surface defect. Once the CeramiGrade Rebuild has reached initial set the material can be separated from surfaces treated with release agent. When CeramiGrade Rebuild is being used to repair leaking pipes, the flow through the pipe should be discontinued until the repair is made and the CeramiGrade Rebuild is set. Any leaking fluid must be wiped from the prepared surface before undertaking the repair. When a second coat is required, this should be done as soon as the first coat has set. within 4 hours

4. Machining Once the CeramiGrade Rebuild has

cured for the minimum time indicated in the Curing Properties Section of the product specification sheet, sanding, grinding and machining etc. can be carried out using standard engineering practices.

5. Cleaning

All equipment should be cleaned IMMEDIATELY after each use with a cleaner. Failure to follow this procedure will result in application equipment becoming unusable.

6. Health and safety

As long as normal good practices are observed CeramiGrade Rebuild can be safely used. A fully detailed Material Safety Data Sheet is included with the set. The information provided in this Instruction sheet is intended as a general guide only. Users should determined the suitability of the product for their own particular purposes by their own tests. Corroded tube plates Eroded impellers 3.06 315 3.06 316 Product specification sheet – Ceramigrade Liner Product Description Identification Application Data Chemical resistance Suitable for permanent immersion at 0 °C 68 °F in a limited range of chemicals. For a more detailed description refer to the Chemical Resistance Chart. Manufactured under a quality program certified to ISO 9002 Health and Safety As long as good practice is observed CeramiGrade Liner can be safely used. Wearing of rubber gloves is advisable during use. Prior to using this product please consult the Safety Data Sheet provided with each packaged product. Mixing Ratio Mixing Ratio Pot Life mins Volume Weight Working Life Activator Base Activator Base 5 °C 10 °C 15°C 0 °C 5 °C 30 °C 35 °C 40 °C 1 4 1 5 45 35 30 5 15 13 10 Curing Time Curing Times in minutes at 5 °C 10 °C 15 °C 0 °C 5 °C 30 °C 35 °C 40 °C ambient temperature Initial Setting Light Loading 300 40 10 180 180 150 130 10 Machining 360 300 70 40 40 10 190 180 Full Mechanical Strength 10 days 9 days 8 days 7 days 7 days 5 days 3 days days Full Chemical Resistance 0 days 15 days 15 days 14 days 14 days 10 days 7 days 3 days Activator Component Base Component Appearance Colour Appearance Colour Liquid ClearAmber Liquid Blue Technical Data PhysMec Properties Density gcm 3 Volume Solids Volume Capacity Slump Resistance Activator Base Mixed cc1000gm mm thickness 1,0 1,67 1,55 100 645 na Recommended Temperature Limits For Application: 5 °C TO 40 °C Compressive Strength ASTM D41 70 MPa 1000 psi Tensile Shear Adhesion ASTM D41 16 MPa 300 psi Abrasion Resistance ASTM D4060 0,09 cc 100 cycles Corrosion Resistance ASTM B117 5000 hours Hardness Shore D ASTM D46 80 Impact Resistance ASTM D56 5 kJm Dry heat Wet heat Minimum temp + 70 °C 158 °F + 60 °C 140 °F - 0 °C - 4 °F Values are determined after 48 hours at 0 °C Service Temperatures PRODUCT NAME PRODUCT NO KIT CONSISTS OF Ceramigrade Liner Product No 102-659276 775 g Base + Activator Engineering Repair Fluid Ceramigrade Liner 1 Mixing Container 0,5 ltr Engineering Repair 1 Pair of Gloves Compound 1 Plastic Spatula Supplied complete with all Gross Weight: 0,9 kg 1 Technical Data Sheet necessary equipment all in one Safety Data Sheets 3.06 317 CeramiGrade Liner is a two component, solvent free, fast curing, synthetic repair fluid. Areas of application : Re-building pumps, impellers, propellers, turbine blades, valves etc.

1. Surface preparation