3.06
36
defects. Take care not to trap air bubbles in deep cavities.
4. Machining Once the RubberGrade 6 Rebuild has
cured for the minimum time indicated in the Curing Properties Section of the
product specification sheet, sanding and grinding can be carried out using
standard engineering practices.
5. Cleaning
All equipment should be cleaned IMMEDIATELY after each use with
a cleaner. Failure to follow this procedure will result in application
equipment becoming unusable.
6. Health and safety
As long as normal good practices are observed RubberGrade 6 Rebuild
can be safely used. A fully detailed Material Safety Data Sheet is
included with the set. The information provided in this Instruction sheet
is intended as a general guide only. Users should determined the
suitability of the product for their own particular purposes by their own
tests.
Gaskets and seals repairs
Electrical insulation repairs
3.06
37
3.06
38
Product specification sheet – Rubbergrade 6 Remould
Product Description
Identification
Application Data
Chemical resistance Suitable for permanent immersion at 0 °C 68 °F in a limited range of chemicals. For a more detailed
description refer to the Chemical Resistance Chart.
Manufactured under a quality program certified to ISO 9002 Health and Safety
As long as good practice is observed Rubbergrade 6 Remould can be safely used. Wearing of rubber gloves is advisable during use. Prior to using this product please consult the Safety Data Sheet
provided with each packaged product.
Mixing Ratio Mixing Ratio
Pot Life mins Volume
Weight Working Life
Activator Base Activator Base 5 °C
10 °C 15°C
0 °C 5 °C
30 °C 35 °C
40 °C -
- -
- 15
10 10
8 8
7 6
5
Curing Time
Curing Times in minutes at 5 °C
10 °C 15 °C
0 °C 5 °C
30 °C 35 °C
40 °C ambient temperature
Initial Setting Light Loading 60
50 35
5 5
15 15
Machining 480
40 180
180 150
150 150
10 Full Mechanical Strength
14 days 10 days 8 days 7 days 7 days 7 days 6 days 5 days Full Chemical Resistance
18 days 15 days 14 days 1 days 1 days 8 days 7 days 7 days
Activator Component Base Component
Appearance Colour
Appearance Colour
Liquid Brown
Liquid Black
Technical Data
PhysMec Properties
Density gcm
3
Volume Solids Volume Capacity
Slump Resistance
Activator Base Mixed cc1000gm
1 1 mm thickness 1,
0,98 1,04
100 96
- Recommended Temperature Limits For Application: 5 °C TO 40 °C
Tensile Strength ASTM D41
7 MPa 1015 psi
Tear Strength ASTM D64
4,5 MPa 650 psi
Elongation ASTM D790
50 Hardness Shore A
ASTM D40 65
Dielectric Strength ASTM D149
- Surface Resistivity
ASTM D57 -
Volume Resistivity ASTM D57
-
Dry heat Wet heat
Minimum temp
+ 80 °C 176 °F + 70 °C 158 °F
- 0 °C - 4 °F Values are determined after 48 hours at 0 °C
Service Temperatures
PRODUCT NAME PRODUCT NO
KIT CONSISTS OF
Rubbergrade 6 Remould Product No 103-659292
3 x 150 g packs Base + Activator Engineering Repair Fluid
Rubbergrade 6 Remould 1 Spatula
0,43 ltr Engineering Repair 1 Applicator
Compound 1 Pair of gloves
Supplied complete with all Gross Weight: 590 g
1 Technical Data Sheet necessary equipment all in one
Safety Data Sheets
3.06
39
RubberGrade 6 ReMould is a two component, solvent free, synthetic
rubber repair compound. Areas of application : hoses, gaskets, rubber
rollers, ducting, impellers, valves etc.
1. Surface preparation
Kategori