CONSTANT SPEEDS Constant speed selection and values. An active constant speed overrides the
12 CONSTANT SPEEDS Constant speed selection and values. An active constant speed overrides the
drive speed reference. See section Constant speeds on page 59 .
Note: If parameter 99.04 is SCALAR, only speeds 1 to 5 and speed 15 are in
use.
12.01 CONST SPEED SEL Activates the constant speeds or selects the activation signal. NOT SEL
1 DI1(SPEED1)
No constant speeds in use
Speed defined by parameter 12.02 is activated through digital input DI1.
1 = active, 0 = inactive.
DI2(SPEED2) Speed defined by parameter 12.03 is activated through digital input DI2.
1 = active, 0 = inactive.
DI3(SPEED3) Speed defined by parameter 12.04 is activated through digital input DI3.
1 = active, 0 = inactive.
DI4(SPEED4) Speed defined by parameter 12.05 is activated through digital input DI4.
1 = active, 0 = inactive.
DI5(SPEED5) Speed defined by parameter 12.06 is activated through digital input DI5.
1 = active, 0 = inactive.
DI6(SPEED6) Speed defined by parameter 12.07 is activated through digital input DI6.
1 = active, 0 = inactive.
DI1,2
Constant speed selection through digital input DI1 and DI2.
DI1
DI2 Constant speed in use
0 0 No constant speed
1 0 Speed defined by parameter 12.02
0 1 Speed defined by parameter 12.03
1 1 Speed defined by parameter 12.04
DI3,4
9 DI5,6
See selection DI1,2 .
10 DI1,2,3
See selection DI1,2 .
Constant speed selection through digital input DI1, DI2 and DI3.
DI1
DI2
DI3 Constant speed in use
0 0 0 No constant speed
1 0 0 Speed defined by parameter 12.02
0 1 0 Speed defined by parameter 12.03
1 1 0 Speed defined by parameter 12.04
0 0 1 Speed defined by parameter 12.05
1 0 1 Speed defined by parameter 12.06
0 1 1 Speed defined by parameter 12.07
1 1 1 Speed defined by parameter 12.08
12 DI4,5,6
DI3,4,5
See selection DI1,2,3.
13 DI3,4,5,6
See selection DI1,2,3.
Constant speed selection through digital input DI3, 4, 5 and 6
DI4 Constant speed in use
0 0 0 0 No constant speed
1 0 0 0 Speed defined by parameter 12.02
0 1 0 0 Speed defined by parameter 12.03
1 1 0 0 Speed defined by parameter 12.04
0 0 1 0 Speed defined by parameter 12.05
1 0 1 0 Speed defined by parameter 12.06
0 1 1 0 Speed defined by parameter 12.07
1 1 1 0 Speed defined by parameter 12.08
0 0 0 1 Speed defined by parameter 12.09
1 0 0 1 Speed defined by parameter 12.10
0 1 0 1 Speed defined by parameter 12.11
1 1 0 1 Speed defined by parameter 12.12
0 0 1 1 Speed defined by parameter 12.13
1 0 1 1 Speed defined by parameter 12.14
0 1 1 1 Speed defined by parameter 12.15
1 1 1 1 Speed defined by parameter 12.16 DI7(SPEED1)
Speed defined by parameter 12.02 is activated through digital input DI7.
1 = active, 0 = inactive.
DI8(SPEED2) Speed defined by parameter 12.03 is activated through digital input DI8.
1 = active, 0 = inactive.
DI9(SPEED3) Speed defined by parameter 12.04 is activated through digital input DI9.
1 = active, 0 = inactive.
DI10(SPEED4) Speed defined by parameter 12.05 is activated through digital input DI10.
1 = active, 0 = inactive.
DI11(SPEED5) Speed defined by parameter 12.06 is activated through digital input DI11.
1 = active, 0 = inactive.
DI12 (SPEED6) Speed defined by parameter 12.07 is activated through digital input DI12.
1 = active, 0 = inactive.
DI7,8
21 DI9,10
See selection DI1,2 .
22 DI11,12
See selection DI1,2 .
See selection DI1,2 .
12.02 CONST SPEED 1 Defines speed 1. An absolute value. Does not include the direction information.
0 … 18000 rpm
Setting range
12.03 CONST SPEED 2 Defines speed 2. An absolute value. Does not include the direction information.
0 … 18000 rpm
Setting range
12.04 CONST SPEED 3 Defines speed 3. An absolute value. Does not include the direction information.
0 … 18000 rpm
Setting range
12.05 CONST SPEED 4 Defines speed 4. An absolute value. Does not include the direction information.
0 … 18000 rpm
Setting range
12.06 CONST SPEED 5 Defines speed 5. An absolute value. Does not include the direction information.
0 … 18000 rpm
Setting range
12.07 CONST SPEED 6 Defines speed 6. An absolute value. Does not include the direction information.
0 … 18000 rpm
Setting range
12.08 CONST SPEED 7 Defines speed 7. An absolute value. Does not include the direction information.
0 … 18000 rpm
Setting range
12.09 CONST SPEED 8 Defines speed 8. An absolute value. Does not include the direction information.
0 … 18000 rpm
Setting range
12.10 CONST SPEED 9 Defines speed 9. An absolute value. Does not include the direction information.
0 … 18000 rpm
Setting range
12.11 CONST SPEED 10 Defines speed 10. An absolute value. Does not include the direction information.
0 … 18000 rpm
Setting range
12.12 CONST SPEED 11 Defines speed 11. An absolute value. Does not include the direction information.
0 … 18000 rpm
Setting range
12.13 CONST SPEED 12 Defines speed 12. An absolute value. Does not include the direction information.
Note: If inching is in use, the parameter defines the inching 1 speed. The sign is taken into account. See chapter Fieldbus control .
-18000 … 18000 rpm Setting range -18000 … 18000
12.14 CONST SPEED 13 Defines speed 13. An absolute value. Does not include the direction information.
Note: If inching is in use, the parameter defines the inching 2 speed. The sign is taken into account. See chapter Fieldbus control .
-18000 … 18000 rpm Setting range -18000 … 18000
12.15 CONST SPEED 14 Defines speed 14. An absolute value. Does not include the direction information.
Note: If the jogging function is in use, the parameter defines the jogging speed. The sign is not taken into account. See section Jogging on page 81 .
0 … 18000 rpm
Setting range
12.16 CONST SPEED 15 Defines speed 15 or Fault speed. The program considers the sign when used
as a fault speed by parameter 30.01 and 30.02 .
-18000 … 18000 rpm Setting range -18000 … 18000