When WinRadius launches, click Yes in the User Account Control dialog box. Click OK. You should see a message on the log screen that the user was added successfully.
c. Click OK. 2. Run as Administrator settings:
a. Right click on the WinRadius.exe icon and select Properties. b. While in the Properties dialog box, select the Compatibility tab. In this tab, select the checkbox for Run this program as administrator in the Privilege Level section. c. Click OK. 3. Run as Administration for each launch: a. Right click on the WinRadius.exe icon and select Run as Administrator.b. When WinRadius launches, click Yes in the User Account Control dialog box.
CCNA Security All contents are Copyright © 1992 –2011 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information. Page 16 of 31 Step 2: Configure the WinRadius server database. a. Start the WinRadius.exe application. WinRadius uses a local database in which it stores user information. When the application is started for the first time, the following messages are displayed: Please go to “SettingsDatabase and create the ODBC for your RADIUS database. Launch ODBC failed. b. Choose Settings Database from the main menu. The following screen is displayed. Click the Configure ODBC Automatically button and then click OK. You should see a message that the ODBC was created successfully. Exit WinRadius and restart the application for the changes to take effect. c. When WinRadius starts again, you should see messages similar to the following displayed. CCNA Security All contents are Copyright © 1992 –2011 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information. Page 17 of 31 d. On which ports is WinRadius listening for authentication and accounting? The authentication port is 1812, and the accounting port is 1813. Step 3: Configure users and passwords on the WinRadius server. Note: The free version of WinRadius can support only five usernames. The usernames are lost if you exit the application and restart it. Any usernames created in previous sessions must be re-created. Note that the first message in the previous screen shows that zero users were loaded. No users had been created prior to this, but this message is displayed each time WinRadius is started, regardless of whether users were created or not. a. From the main menu, select Operation Add User. b. Enter the username RadUser with a password of RadUserpass. Remember that passwords are case-sensitive.c. Click OK. You should see a message on the log screen that the user was added successfully.
Step 4: Clear the log display. From the main menu, choose Log Clear. CCNA Security All contents are Copyright © 1992 –2011 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information. Page 18 of 31 Step 5: Test the new user added using the WinRadius test utility. a. A WinRadius testing utility is included in the downloaded zip file. Navigate to the folder where you unzipped the WinRadius.zip file and locate the file named RadiusTest.exe. b. Start the RadiusTest application, and enter the IP address of this RADIUS server 192.168.1.3, username RadUser, and password RadUserpass as shown. Do not change the default RADIUS port number of 1813 and the RADIUS password of WinRadius.c. Click Send and you should see a Send Access_Request message indicating the server at
Parts
» CCNA Security 1.1 Instructor Lab Manual
» Lab A: Researching Network Attacks and Security Audit Tools
» Lab A: Securing the Router for Administrative Access
» Use the username command to create the user ID with the highest possible privilege level and a
» Issue the undebug all or the no debug ntp all command to turn off debugging.
» Click OK in the Commands Delivery Status window.
» Use the show logging command to see the type and level of logging enabled.
» Save the running config to the startup config using the copy run start command.
» Lab A: Securing Administrative Access Using AAA and RADIUS
» Click Send and you should see a Send Access_Request message indicating the server at
» Clear the log on the WinRadius server by choosing Log Clear from the main menu.
» Lab A: Configuring CBAC and Zone-Based Firewalls
» Issue the show run command to review the current basic configuration on R1.
» Display the Extended ACL named autosec_firewall_acl, which is applied to S000 inbound.
» Display the Extended ACL named autosec_firewall_acl that is applied to S000 inbound.
» Click Finish to complete the Firewall wizard.
» Lab A: Configuring an Intrusion Prevention System IPS Using the CLI and CCP
» From the R1 CLI, verify that the directory is present using the dir flash: or dir flash:ipsdir
» Apply the IPS rule to an interface with the ip ips name direction command in interface
» Verify connectivity between R1 and PC-A, the TFTP server, using the ping command.
» Use the show ip ips all command to see an IPS configuration status summary. To which
» For Protocol, select tftp from the drop-down menu. Enter the IP address of the PC-C TFTP server
» Lab A: Securing Layer 2 Switches Instructor Version
» From the router R1 CLI, use the show interface command and record the MAC address of the
» Set the SPAN source interface using the monitor session command in global configuration mode.
» Lab A: Exploring Encryption Methods Instructor
» Lab A: Configuring a Site-to-Site VPN Using Cisco IOS and CCP
» Verify the IKE policy with the show crypto isakmp policy command.
» Save the running config to the startup config for R1 and R3 using the copy run start command.
» Click the Launch the selected task button to begin the CCP Site-to-Site VPN wizard.
» Lab B: Configuring a Remote Access VPN Server and Client
» In the Command Delivery Status window, click OK. How many commands are delivered? 103 with
» Lab C Optional: Configuring a Remote Access VPN Server and Client
» Lab A: Security Policy Development and Implementation
» Verify that R1 and R3 have made an association with R2 using the show ntp associations
» Choose FastEthernet 01 as the Inside Trusted interface and Serial 001 as the Outside Untrusted
» From PC-A, Telnet to R2 at IP address 10.1.1.2 using the vty line password ciscovtypass.
» If the ipsdir directory is not listed, create it.
» Secure the router running configuration and securely archive it in persistent storage flash.
» Lab A: Configuring ASA Basic Settings and Firewall Using CLI
» Display the ASA file system using the show file system command to determine what prefixes are
» Display the current running configuration using the show running-config command.
» You can configure the ASA to accept HTTPS connections using the http command. This allows
» Issue the show route command to display the ASA routing table and the static default route just
» Save the RSA keys to persistent flash memory using either the copy run start or write mem
» Lab B: Configuring ASA Basic Settings and Firewall Using ASDM
» View this Access Rule in ASDM by choosing Configuration Firewall Access Rules. It appears
» Lab C: Configuring Clientless and AnyConnect Remote Access SSL VPNs Using ASDM
» Enable HTTP access to R1 using the ip http server command in global config mode. Also set
» From the Add Bookmark List window, click Add to open the Add Bookmark window. Enter Web Mail as
» Lab D: Configuring a Site-to-Site IPsec VPN Using CCP and ASDM
» Use the reload command to restart the ASA. This will cause the ASA to come up in CLI Setup
» In the Peer Identity section, select Peer with static IP address and enter the IP address of the
Show more