Check the R1 running configuration for lines containing the command radius. The following From the WinRadius main menu choose Settings System.
b. Check the R1 running configuration for lines containing the command radius. The following
command displays all running config lines that include the text “radius”. R1 show run | incl radius aaa authentication login default group radius none radius-server host 192.168.1.3 auth-port 1645 acct-port 1646 key 7 097B47072B04131B1E1F Output omitted c. What are the default R1 Cisco IOS UDP port numbers for the RADIUS server? 1645 and 1646 Step 4: Check the default port numbers on the WinRadius server on PC-A.a. From the WinRadius main menu choose Settings System.
b. What are the default WinRadius UDP port numbers? 1812 and 1813 Note: The early deployment of RADIUS was done using UDP port number 1645 for authentication and 1646 for accounting, which conflicts with the datametrics service. Because of this conflict, RFC 2865 officially assigned port numbers 1812 and 1813 for RADIUS. Step 5: Change the RADIUS port numbers on R1 to match the WinRadius server. Unless specified otherwise, the Cisco IOS RADIUS configuration defaults to UDP port numbers 1645 and 1646. Either the router Cisco IOS port numbers must be changed to match the port number of the RADIUS server or the RADIUS server port numbers must be changed to match the port numbers of the Cisco IOS router. In this step, you modify the IOS port numbers to those of the RADIUS server, which are specified in RFC 2865. a. Remove the previous configuration using the following command. R1config no radius-server host 192.168.1.3 auth-port 1645 acct-port 1646 b. Issue the radius-server host command again and this time specify port numbers 1812 and 1813, along with the IP address and secret key for the RADIUS server. R1config radius-server host 192.168.1.3 auth-port 1812 acct-port 1813 key WinRadius CCNA Security All contents are Copyright © 1992 –2011 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information. Page 21 of 31 Step 6: Test your configuration by logging into the console on R1. a. Exit to the initial router screen that displays: R1 con0 is now available, Press RETURN to get started. b. Log in again with the username of RadUser and password of RadUserpass. Were you able to login?Parts
» CCNA Security 1.1 Instructor Lab Manual
» Lab A: Researching Network Attacks and Security Audit Tools
» Lab A: Securing the Router for Administrative Access
» Use the username command to create the user ID with the highest possible privilege level and a
» Issue the undebug all or the no debug ntp all command to turn off debugging.
» Click OK in the Commands Delivery Status window.
» Use the show logging command to see the type and level of logging enabled.
» Save the running config to the startup config using the copy run start command.
» Lab A: Securing Administrative Access Using AAA and RADIUS
» Click Send and you should see a Send Access_Request message indicating the server at
» Clear the log on the WinRadius server by choosing Log Clear from the main menu.
» Lab A: Configuring CBAC and Zone-Based Firewalls
» Issue the show run command to review the current basic configuration on R1.
» Display the Extended ACL named autosec_firewall_acl, which is applied to S000 inbound.
» Display the Extended ACL named autosec_firewall_acl that is applied to S000 inbound.
» Click Finish to complete the Firewall wizard.
» Lab A: Configuring an Intrusion Prevention System IPS Using the CLI and CCP
» From the R1 CLI, verify that the directory is present using the dir flash: or dir flash:ipsdir
» Apply the IPS rule to an interface with the ip ips name direction command in interface
» Verify connectivity between R1 and PC-A, the TFTP server, using the ping command.
» Use the show ip ips all command to see an IPS configuration status summary. To which
» For Protocol, select tftp from the drop-down menu. Enter the IP address of the PC-C TFTP server
» Lab A: Securing Layer 2 Switches Instructor Version
» From the router R1 CLI, use the show interface command and record the MAC address of the
» Set the SPAN source interface using the monitor session command in global configuration mode.
» Lab A: Exploring Encryption Methods Instructor
» Lab A: Configuring a Site-to-Site VPN Using Cisco IOS and CCP
» Verify the IKE policy with the show crypto isakmp policy command.
» Save the running config to the startup config for R1 and R3 using the copy run start command.
» Click the Launch the selected task button to begin the CCP Site-to-Site VPN wizard.
» Lab B: Configuring a Remote Access VPN Server and Client
» In the Command Delivery Status window, click OK. How many commands are delivered? 103 with
» Lab C Optional: Configuring a Remote Access VPN Server and Client
» Lab A: Security Policy Development and Implementation
» Verify that R1 and R3 have made an association with R2 using the show ntp associations
» Choose FastEthernet 01 as the Inside Trusted interface and Serial 001 as the Outside Untrusted
» From PC-A, Telnet to R2 at IP address 10.1.1.2 using the vty line password ciscovtypass.
» If the ipsdir directory is not listed, create it.
» Secure the router running configuration and securely archive it in persistent storage flash.
» Lab A: Configuring ASA Basic Settings and Firewall Using CLI
» Display the ASA file system using the show file system command to determine what prefixes are
» Display the current running configuration using the show running-config command.
» You can configure the ASA to accept HTTPS connections using the http command. This allows
» Issue the show route command to display the ASA routing table and the static default route just
» Save the RSA keys to persistent flash memory using either the copy run start or write mem
» Lab B: Configuring ASA Basic Settings and Firewall Using ASDM
» View this Access Rule in ASDM by choosing Configuration Firewall Access Rules. It appears
» Lab C: Configuring Clientless and AnyConnect Remote Access SSL VPNs Using ASDM
» Enable HTTP access to R1 using the ip http server command in global config mode. Also set
» From the Add Bookmark List window, click Add to open the Add Bookmark window. Enter Web Mail as
» Lab D: Configuring a Site-to-Site IPsec VPN Using CCP and ASDM
» Use the reload command to restart the ASA. This will cause the ASA to come up in CLI Setup
» In the Peer Identity section, select Peer with static IP address and enter the IP address of the
Show more