From the PC-A command line, issue the ipconfig command. Choose Status Statistics. Click the Tunnel Details tab.
b. From the PC-A command line, issue the ipconfig command.
What is the IP address of the first Local Area Connection? 192.168.1.3 What is the IP address of Local Area Connection 2? 192.168.3.100 Step 2: Close the VPN connection and reopen it. a. Click the Disconnect icon in the VPN Client window to close the VPN-R3 connection. b. Click the Connect icon and log in again as VPNuser1. What is the IP address of Local Area Connection 2 now? 192.168.3.101 Note: Each time you disconnect and reconnect to the VPN server, you receive a new IP address until the limit is reached. Step 3: Check the tunnel statistics.a. Choose Status Statistics. Click the Tunnel Details tab.
CCNA Security All contents are Copyright © 1992 –2012 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information. Page 23 of 33 b. What is the current address obtained from the R3 VPN server and what is the range of addresses that can be assigned? Answers will vary. Currently the IP address is 192.168.3.101, but it can range from 192.168.3.100 through 192.168.3.150. The pool of addresses was defined in Task 2. What is the VPN server address? 10.2.2.1 How many packets have been encrypted? Answers will vary What is the encryption method? 168-bit 3-DES What is the authentication method? HMAC-SHA1 c. Leave the VPN Client Statistics window open. Step 4: Test access from the client PC-A using the VPN connection. a. With the VPN connection from computer PC-A to router R3 activated, open a command prompt on PC-A and ping the PC-C IP address at 192.168.3.3 on the R3 LAN. Are the pings successful? Yes. The pings are successful. PC-A has an IP address 192.168.3.101 in this case that was assigned by the VPN server. PC-A can access the internal PC-C host on network 192.168.3.024 because both hosts are on the same subnet. b. How many packets have now been encrypted? Answers will vary, but the number should increase by four. Step 5: Check the Cisco IOS message on R3 when the tunnel is created. Open the console connection for R3 and locate the message displayed indicating that the virtual interface came up when the VPN Client connection was made. What is the name of the interface on R3 that is activated for the VPN? Interface Virtual-Access2 R3 Feb 20 12:09:08.907: LINEPROTO-5-UPDOWN: Line protocol on Interface Virtual-Access2, changed state to up R3 CCNA Security All contents are Copyright © 1992 –2012 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information. Page 24 of 33 Step 6: Verify the VPN connection information for PC-A.a. From the PC-A command prompt, issue the ipconfig all command to see the network
Parts
» CCNA Security 1.1 Instructor Lab Manual
» Lab A: Researching Network Attacks and Security Audit Tools
» Lab A: Securing the Router for Administrative Access
» Use the username command to create the user ID with the highest possible privilege level and a
» Issue the undebug all or the no debug ntp all command to turn off debugging.
» Click OK in the Commands Delivery Status window.
» Use the show logging command to see the type and level of logging enabled.
» Save the running config to the startup config using the copy run start command.
» Lab A: Securing Administrative Access Using AAA and RADIUS
» Click Send and you should see a Send Access_Request message indicating the server at
» Clear the log on the WinRadius server by choosing Log Clear from the main menu.
» Lab A: Configuring CBAC and Zone-Based Firewalls
» Issue the show run command to review the current basic configuration on R1.
» Display the Extended ACL named autosec_firewall_acl, which is applied to S000 inbound.
» Display the Extended ACL named autosec_firewall_acl that is applied to S000 inbound.
» Click Finish to complete the Firewall wizard.
» Lab A: Configuring an Intrusion Prevention System IPS Using the CLI and CCP
» From the R1 CLI, verify that the directory is present using the dir flash: or dir flash:ipsdir
» Apply the IPS rule to an interface with the ip ips name direction command in interface
» Verify connectivity between R1 and PC-A, the TFTP server, using the ping command.
» Use the show ip ips all command to see an IPS configuration status summary. To which
» For Protocol, select tftp from the drop-down menu. Enter the IP address of the PC-C TFTP server
» Lab A: Securing Layer 2 Switches Instructor Version
» From the router R1 CLI, use the show interface command and record the MAC address of the
» Set the SPAN source interface using the monitor session command in global configuration mode.
» Lab A: Exploring Encryption Methods Instructor
» Lab A: Configuring a Site-to-Site VPN Using Cisco IOS and CCP
» Verify the IKE policy with the show crypto isakmp policy command.
» Save the running config to the startup config for R1 and R3 using the copy run start command.
» Click the Launch the selected task button to begin the CCP Site-to-Site VPN wizard.
» Lab B: Configuring a Remote Access VPN Server and Client
» In the Command Delivery Status window, click OK. How many commands are delivered? 103 with
» Lab C Optional: Configuring a Remote Access VPN Server and Client
» Lab A: Security Policy Development and Implementation
» Verify that R1 and R3 have made an association with R2 using the show ntp associations
» Choose FastEthernet 01 as the Inside Trusted interface and Serial 001 as the Outside Untrusted
» From PC-A, Telnet to R2 at IP address 10.1.1.2 using the vty line password ciscovtypass.
» If the ipsdir directory is not listed, create it.
» Secure the router running configuration and securely archive it in persistent storage flash.
» Lab A: Configuring ASA Basic Settings and Firewall Using CLI
» Display the ASA file system using the show file system command to determine what prefixes are
» Display the current running configuration using the show running-config command.
» You can configure the ASA to accept HTTPS connections using the http command. This allows
» Issue the show route command to display the ASA routing table and the static default route just
» Save the RSA keys to persistent flash memory using either the copy run start or write mem
» Lab B: Configuring ASA Basic Settings and Firewall Using ASDM
» View this Access Rule in ASDM by choosing Configuration Firewall Access Rules. It appears
» Lab C: Configuring Clientless and AnyConnect Remote Access SSL VPNs Using ASDM
» Enable HTTP access to R1 using the ip http server command in global config mode. Also set
» From the Add Bookmark List window, click Add to open the Add Bookmark window. Enter Web Mail as
» Lab D: Configuring a Site-to-Site IPsec VPN Using CCP and ASDM
» Use the reload command to restart the ASA. This will cause the ASA to come up in CLI Setup
» In the Peer Identity section, select Peer with static IP address and enter the IP address of the
Show more