Click the Launch the selected task button to begin the CCP Site-to-Site VPN wizard.
c. Click the Launch the selected task button to begin the CCP Site-to-Site VPN wizard.
d. On the initial Site-to-Site VPN Wizard window, the Quick Setup option is selected by default. Click the View Defaults button to see what settings this option uses. What type of encryption does the default transform set use? ESP-3DES e. From the initial Site-to-Site VPN wizard window, choose the Step by Step wizard, and then click Next. Why would you use this option over the Quick setup option? So that you have more control over the VPN settings used. Step 4: Configure basic VPN connection information settings. a. From the VPN Connection Information window, select the interface for the connection, which should be R1 Serial000. b. In the Peer Identity section, select Peer with static IP address and enter the IP address of remote peer R3 S001 10.2.2.1. c. In the Authentication section, click Pre-shared Keys, and enter the pre-shared VPN key cisco12345. Re-enter the key for confirmation. This key authenticates the initial exchange to establish the Security Association between devices. When finished, your screen should look similar to the following. Once you have entered these settings correctly, click Next. CCNA Security All contents are Copyright © 1992 –2012 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information. Page 18 of 40 Step 5: Configure IKE policy parameters. IKE policies are used while setting up the control channel between the two VPN endpoints for key exchange. This is also referred to as the IKE secure association SA. In contrast, the IPsec policy is used during IKE Phase II to negotiate an IPsec security association to pass target data traffic. a. In the IKE Proposals window, a default policy proposal is displayed. You can use this one or create a new one. What function does this IKE proposal serve? The IKE proposal specifies the encryption algorithm, authentication algorithm, and key exchange method used by this router when negotiating a VPN connection with a remote router.b. Click the Add button to create a new IKE policy.
Parts
» CCNA Security 1.1 Instructor Lab Manual
» Lab A: Researching Network Attacks and Security Audit Tools
» Lab A: Securing the Router for Administrative Access
» Use the username command to create the user ID with the highest possible privilege level and a
» Issue the undebug all or the no debug ntp all command to turn off debugging.
» Click OK in the Commands Delivery Status window.
» Use the show logging command to see the type and level of logging enabled.
» Save the running config to the startup config using the copy run start command.
» Lab A: Securing Administrative Access Using AAA and RADIUS
» Click Send and you should see a Send Access_Request message indicating the server at
» Clear the log on the WinRadius server by choosing Log Clear from the main menu.
» Lab A: Configuring CBAC and Zone-Based Firewalls
» Issue the show run command to review the current basic configuration on R1.
» Display the Extended ACL named autosec_firewall_acl, which is applied to S000 inbound.
» Display the Extended ACL named autosec_firewall_acl that is applied to S000 inbound.
» Click Finish to complete the Firewall wizard.
» Lab A: Configuring an Intrusion Prevention System IPS Using the CLI and CCP
» From the R1 CLI, verify that the directory is present using the dir flash: or dir flash:ipsdir
» Apply the IPS rule to an interface with the ip ips name direction command in interface
» Verify connectivity between R1 and PC-A, the TFTP server, using the ping command.
» Use the show ip ips all command to see an IPS configuration status summary. To which
» For Protocol, select tftp from the drop-down menu. Enter the IP address of the PC-C TFTP server
» Lab A: Securing Layer 2 Switches Instructor Version
» From the router R1 CLI, use the show interface command and record the MAC address of the
» Set the SPAN source interface using the monitor session command in global configuration mode.
» Lab A: Exploring Encryption Methods Instructor
» Lab A: Configuring a Site-to-Site VPN Using Cisco IOS and CCP
» Verify the IKE policy with the show crypto isakmp policy command.
» Save the running config to the startup config for R1 and R3 using the copy run start command.
» Click the Launch the selected task button to begin the CCP Site-to-Site VPN wizard.
» Lab B: Configuring a Remote Access VPN Server and Client
» In the Command Delivery Status window, click OK. How many commands are delivered? 103 with
» Lab C Optional: Configuring a Remote Access VPN Server and Client
» Lab A: Security Policy Development and Implementation
» Verify that R1 and R3 have made an association with R2 using the show ntp associations
» Choose FastEthernet 01 as the Inside Trusted interface and Serial 001 as the Outside Untrusted
» From PC-A, Telnet to R2 at IP address 10.1.1.2 using the vty line password ciscovtypass.
» If the ipsdir directory is not listed, create it.
» Secure the router running configuration and securely archive it in persistent storage flash.
» Lab A: Configuring ASA Basic Settings and Firewall Using CLI
» Display the ASA file system using the show file system command to determine what prefixes are
» Display the current running configuration using the show running-config command.
» You can configure the ASA to accept HTTPS connections using the http command. This allows
» Issue the show route command to display the ASA routing table and the static default route just
» Save the RSA keys to persistent flash memory using either the copy run start or write mem
» Lab B: Configuring ASA Basic Settings and Firewall Using ASDM
» View this Access Rule in ASDM by choosing Configuration Firewall Access Rules. It appears
» Lab C: Configuring Clientless and AnyConnect Remote Access SSL VPNs Using ASDM
» Enable HTTP access to R1 using the ip http server command in global config mode. Also set
» From the Add Bookmark List window, click Add to open the Add Bookmark window. Enter Web Mail as
» Lab D: Configuring a Site-to-Site IPsec VPN Using CCP and ASDM
» Use the reload command to restart the ASA. This will cause the ASA to come up in CLI Setup
» In the Peer Identity section, select Peer with static IP address and enter the IP address of the
Show more