Verify connectivity between R3 and PC-C, the TFTP server, using the ping command. Click the Launch IPS Rule Wizard button to open the Welcome to the IPS Policies Wizard window.
a. Verify connectivity between R3 and PC-C, the TFTP server, using the ping command.
b. Verify that the PC has the IPS Signature package file in a directory on the TFTP server. This file is typically named IOS-Sxxx-CLI.pkg, where xxx is the signature file version. Note: If this file is not present, contact your instructor before continuing. c. Start Tftpd32 or another TFTP server and set the default directory to the one with the IPS Signature package. The Tftpd32 screen is shown here with the C:\Program Files\Tftpd32\IPS directory contents displayed. Take note of the filename for use in the next step. d. What is the name of the signature file? IOS-S364-CLI.pkg for demonstration purposes with this lab CCNA Security All contents are Copyright © 1992 –2012 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information. Page 24 of 50 Task 4: Use CCP to Configure IPS Step 1: Access CCP and discover R3. a. Start CCP on PC-C. In the Manage Devices window, add R3 IP address 192.168.3.1 in the first IP address field. Enter admin in the Username field, and cisco12345 in the Password field. b. At the CCP Dashboard, click the Discover button to discover and connect to R3. If discovery fails, click the Discovery Details button to determine the problem. Note: If you are using Java version 1.6 or later, the Java console displays by default when CCP is run. If the Java console displays, you can close it. You can also start the Java plug-in application and choose Advanced Java Console Do not start console. The Java console will not appear again unless you change the setting. Step 2: Use the CCP IPS Wizard to configure Cisco IOS IPS. a. Click the Configure button at the top of the CCP screen and then choose Security Intrusion Prevention Create IPS.b. Click the Launch IPS Rule Wizard button to open the Welcome to the IPS Policies Wizard window.
c. Read the information on the IPS Policies Wizard screen to become familiar with what the wizard does. Click Next. CCNA Security All contents are Copyright © 1992 –2012 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information. Page 25 of 50 Note: SDEE dialog boxes might appear. Read the information and click OK for each dialog box. d. In the Select Interfaces window, check the Inbound check box for Fast Ethernet01 and Serial001. Click Next. Note: Selecting inbound on both interfaces allows IPS to monitor attacks on the router from the internal and external network. CCNA Security All contents are Copyright © 1992 –2012 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information. Page 26 of 50 e. In the Signature File and Public Key window, click the ellipsis … button next to Specify the Signature File You Want to Use with IOS IPS to open the Specify Signature File window. Confirm that the Specify signature file using URL option is chosen.f. For Protocol, select tftp from the drop-down menu. Enter the IP address of the PC-C TFTP server
Parts
» CCNA Security 1.1 Instructor Lab Manual
» Lab A: Researching Network Attacks and Security Audit Tools
» Lab A: Securing the Router for Administrative Access
» Use the username command to create the user ID with the highest possible privilege level and a
» Issue the undebug all or the no debug ntp all command to turn off debugging.
» Click OK in the Commands Delivery Status window.
» Use the show logging command to see the type and level of logging enabled.
» Save the running config to the startup config using the copy run start command.
» Lab A: Securing Administrative Access Using AAA and RADIUS
» Click Send and you should see a Send Access_Request message indicating the server at
» Clear the log on the WinRadius server by choosing Log Clear from the main menu.
» Lab A: Configuring CBAC and Zone-Based Firewalls
» Issue the show run command to review the current basic configuration on R1.
» Display the Extended ACL named autosec_firewall_acl, which is applied to S000 inbound.
» Display the Extended ACL named autosec_firewall_acl that is applied to S000 inbound.
» Click Finish to complete the Firewall wizard.
» Lab A: Configuring an Intrusion Prevention System IPS Using the CLI and CCP
» From the R1 CLI, verify that the directory is present using the dir flash: or dir flash:ipsdir
» Apply the IPS rule to an interface with the ip ips name direction command in interface
» Verify connectivity between R1 and PC-A, the TFTP server, using the ping command.
» Use the show ip ips all command to see an IPS configuration status summary. To which
» For Protocol, select tftp from the drop-down menu. Enter the IP address of the PC-C TFTP server
» Lab A: Securing Layer 2 Switches Instructor Version
» From the router R1 CLI, use the show interface command and record the MAC address of the
» Set the SPAN source interface using the monitor session command in global configuration mode.
» Lab A: Exploring Encryption Methods Instructor
» Lab A: Configuring a Site-to-Site VPN Using Cisco IOS and CCP
» Verify the IKE policy with the show crypto isakmp policy command.
» Save the running config to the startup config for R1 and R3 using the copy run start command.
» Click the Launch the selected task button to begin the CCP Site-to-Site VPN wizard.
» Lab B: Configuring a Remote Access VPN Server and Client
» In the Command Delivery Status window, click OK. How many commands are delivered? 103 with
» Lab C Optional: Configuring a Remote Access VPN Server and Client
» Lab A: Security Policy Development and Implementation
» Verify that R1 and R3 have made an association with R2 using the show ntp associations
» Choose FastEthernet 01 as the Inside Trusted interface and Serial 001 as the Outside Untrusted
» From PC-A, Telnet to R2 at IP address 10.1.1.2 using the vty line password ciscovtypass.
» If the ipsdir directory is not listed, create it.
» Secure the router running configuration and securely archive it in persistent storage flash.
» Lab A: Configuring ASA Basic Settings and Firewall Using CLI
» Display the ASA file system using the show file system command to determine what prefixes are
» Display the current running configuration using the show running-config command.
» You can configure the ASA to accept HTTPS connections using the http command. This allows
» Issue the show route command to display the ASA routing table and the static default route just
» Save the RSA keys to persistent flash memory using either the copy run start or write mem
» Lab B: Configuring ASA Basic Settings and Firewall Using ASDM
» View this Access Rule in ASDM by choosing Configuration Firewall Access Rules. It appears
» Lab C: Configuring Clientless and AnyConnect Remote Access SSL VPNs Using ASDM
» Enable HTTP access to R1 using the ip http server command in global config mode. Also set
» From the Add Bookmark List window, click Add to open the Add Bookmark window. Enter Web Mail as
» Lab D: Configuring a Site-to-Site IPsec VPN Using CCP and ASDM
» Use the reload command to restart the ASA. This will cause the ASA to come up in CLI Setup
» In the Peer Identity section, select Peer with static IP address and enter the IP address of the
Show more