78
SPEKTEK ALAT LABORATORIUM PENGEMBANGAN INDUSTRI TEKNOLOGI KEPOLISIAN KSA T.A. 2011.
h. Measuring device and analyzer for network cabling and fiber optic
1 LAN Cable Testers SPECIFICATION
a General Specification
• Modular design supports copper certification, fiber loss, OTDR testing
• Unmatched speed for Cat 6A, Class FA and all current standards
• Have ability to system manages job requirements and progress from set-up to
systems acceptance, making sure all tests are completed •
Touch screen user interface simplifies set-up, and eliminates •
Have a management software to Analyze test results and create professional test reports
• Graphically displays the source of failures including crosstalk, return loss and
shield faults for faster troubleshooting •
ETL Verified to IEC Level V – the most stringent accuracy requirement •
Endorsed by cabling vendors worldwide •
Built in Alien Crosstalk testing capability b
Technical Specification • Level V accuracy : Specified to 1 GHz
• Resistance Unbalance measurement : Supports IEEE 802.3af and IEEE
802.3at PoE operation that Found in TIA, ISO and IEEE standards • TCL and ELTCTL balance measurements : Good balance means better
immunity to external noise, Found in TIA and ISO standards and Critical in noise environments
• Shield effectiveness test : Grounded racks in data centers can cause a false Wire Map PASS, If the shield is open, the Wire Map tester may still report a
PASS – not DSX, then show Distance to open shield • Built in Project Management : Configure multiple setups in advance to
Prevents errors such as incorrect test limits and Export setups to tester via USB or thumb drive
• Built in Alien Crosstalk measurement : Critical for supporting 10GBASE-T in data centers which is Specified in ISO and TIA standards
• CDNEXT measurement : Common mode to Differential mode near end crosstalk measurement and Diagnostic tool for Alien Crosstalk issues
• Store over 10,000 test results : Category 6AClass EA with full plot data and diagnostic data
• NEXT and Return Loss diagnostics : HDTDR to locate impedance anomalies – must be able to store and export with result and HDTDX to locate crosstalk
issues - must be able to store and export with result • Results management : Includes statistical analysis with Built in PDF export
2 OTDR Fiber Optic Test Kit SPECIFICATION
a General Specification
1 Fastest time to certify – two fibers at two wavelengths in three seconds.
2 Have Encircled Flux compliant as required by ANSITIA and ISOIEC with no
additional test cords 3
Merged Tier 1 Basic Tier 2 Extended testing and reporting when paired with OTDR
4 Convenient quad module supports both multimode and singlemode loss
testing 5
Extended singlemode distance range to 130km 6
The OTDR is the Industry’s shortest event and attenuation dead zones
79
SPEKTEK ALAT LABORATORIUM PENGEMBANGAN INDUSTRI TEKNOLOGI KEPOLISIAN KSA T.A. 2011.
7 Accelerate fiber certification with the fastest set-up and trace times
8 Improve resource utilization with custom configurations for projects and
users 9
Simplify use with Data Center OTDR mode and Event Map view b
Technical Specification 1
Encircled Flux compliant : Source must be EF compliant, Matched test reference cords per TIA TSB-4979 and Required in ANSITIA-526-14-B and
IEC 61280-4-2.
2 3 second Autotest:
Multimode at 850 nm and 1300 nm on two fibers Singlemode at 1310 nm and 1550 nm on two fibers
3 1 Jumper reference for SC, LC, ST and FC connectors : Required for
cabling warranty application and Requires interchangeable adapters on the input ports
4 Test reference cord verification : Built in wizard guides users through the
reference procedure Includes a step to verify TRCs TRC verification results stored automatically
5 Built in Visual Fault Locator : Locate bends and cracks in fiber rackstrays
and also Verify polarity 6
Quad fiber modul : •
Dual output ports for 8501300 nm and 13101550 nm •
Single input port calibrated for 850 nm, 1300 nm, 1310 nm and 1550 nm
7 Store two fiber results at once : Remote results automatically sent to main
unit for analysis and storage 8
Fiber Inspection : Allows the attachment of a USB camera, Store results internally and Merges fiber inspection results with Tier 1 and Tier 2 results
9 Extended distance:
• 12 km for multimode
• 130 km for singlemode
10 Built in talk set: Full duplex communication over multimode and
singlemode links 11
Results management : Statistical analysis, Merger OLTS, OTDR and fiber inspection results with Built in PDF export
c Must have Supporting letter from principal and supporting letter from local
support Distributor in indonesia
i. Specific measuring devices wired LAN Network