Examination Graduation Certificates Common Requirements
3.7.1.7 Graduation Certificates
CAR 423.08 3cvii References Result A-1 Does the certificate include the following: - the name and location of the facility; - the type of training; - the students full name; - the date of course completion; - an embossed raised seal; - the signature of authorised officials; and - the DOT course approval number? OK FDG NA A-2 Does the TCM list the names and signatures of individuals authorised to sign certificates? Is this list up to date? TCM OK FDG NA A-3 Does the TCM contain an up-to-date copy of a sample certificate? TCM OK FDG NA Items Certified – Completed by: Page 86 Part 2 ✈ Chapter 3 - Checklists MRA – 1st Edition September 1998 Part 2 ✈ Chapter 2 - Airworthiness Audit Policy and Procedures3.7.1.8 Instructors
CAR 423.083b References Result A-1 Does the organisation have an appropriate number of instructors licensed or experienced in aircraft maintenance? Have they been trained in instructional techniques? TCM OK FDG NA A-2 Is the instructor-student ratio appropriate for the type of training? Refer to the section on class size. TCM OK FDG NA A-3 Are specialist instructors inexperienced in aircraft maintenance giving instruction on that subject? TCM OK FDG NA A-4 Does the organisation have a program for the evaluation of instructors? Does it address teaching techniques, technical accuracy and conformance to course objectives? TCM OK FDG NA A-5 Does the organisation have a structured professional development program in place? Does this program ensure the continual updating of faculty members knowledge and experience? TCM OK FDG NA Items Certified - Completed by:3.7.1.9 Organizational Chart
References Result A-1 Does the TCM include an organisational chart? TCM OK FDG NA Part 2 ✈ Chapter 3 - Checklists Page 87 Part 2 - Airworthiness Audit Policy and Procedures MRA – 1 st Edition September 1998 References Result A-2 Does the chart show the responsibilities and reporting levels of each faculty member? TCM OK FDG NA A-3 If an individual reports to more than one manager, does the chart define which manager is responsible for which function? TCM OK FDG NA A-4 Does the TCM describe the duties and responsibilities of each reporting level? Are these descriptions accurate? TCM OK FDG NA Items Certified – Completed by:3.7.1.10 Facilities CAR 423.08 3a
References Result A-1 Does the TCM include a floor plan of the facility? TCM OK FDG NA A-2 Does the facility have proper heating, lighting and ventilation to accommodate the maximum number of students? TCM OK FDG NA A-3 Are classrooms isolated from all interruptions? TCM OK FDG NA A-4 Do classrooms have the following equipment: - proper seating and suitable writing surfaces for students; - proper writing surfaces for the instructor, such as a blackboard, whiteboard or flipchart; and - a desk andor podium for the instructor? TCM OK FDG NAParts
» Initial Certification Audit Audit Types
» Resource Allocation Criteria Frequency
» Financial Change Labour Difficulties
» Management Practices Risk Indicators
» Poor Internal Audit or Quality Assurance Program
» Change in Operational Scope or Additional Authorities
» Changes in Contracting for Services
» Additions or Changes to Product Line
» Purpose Co-ordination Unity of Control
» Qualifications Principal Inspector Restrictions
» Inconsistencies — Civil Aviation Approvals Parallel Report
» Airworthiness Operations Specialist Audit
» Responsibilities Convening Authority CA
» Terms of Reference Qualifications
» Terms of Reference Qualifications Responsibilities
» Team Selection Observer Pre-Audit
» General Entry Meeting Physical Audit
» Pre-Audit Checklists Interviews Evaluation
» Confirmation Request Form CRF
» Completion of Audit Finding Form
» Daily Briefings Exit Meeting
» General Audit Report Post-Audit
» Parallel Report Follow-Up Post-Audit
» Corrective Action Plan Audit Follow-Up
» Audit Philosophy Applied Standard
» Purpose Policy and Organisation
» Applicability Policy and Organisation
» Approved Maintenance Organizations AMOs
» Foreign Approved Maintenance Organizations FAMOs
» Airworthiness Engineering Organizations AEOs
» Conduct of the Audit Team Use of Checklists
» Maintenance Policy Manual or Maintenance Control Manual
» Technical PublicationsLibrary Approved Maintenance Organizations
» Personnel Approved Maintenance Organizations
» Maintenance Training Approved Maintenance Organizations
» Technical Records Approved Maintenance Organizations
» FuellingDefuelling Approved Maintenance Organizations
» De-Icing ProceduresEquipment Approved Maintenance Organizations
» Service Difficulty Reporting Approved Maintenance Organizations
» Defect Control Deferral Approved Maintenance Organizations
» Sample Aircraft for Conformance
» Sub-base Approved Maintenance Organizations
» Company Quality Audits Approved Maintenance Organizations
» Receiving Inspections Approved Maintenance Organizations
» Maintenance Schedule Approved Maintenance Organizations
» ReliabilityMaintenance Development Programs Approved Maintenance Organizations
» SupportOverhaul Shops Approved Maintenance Organizations
» Control of PartsMaterial Approved Maintenance Organizations
» TestingMeasuring Equipment Maintenance Contracts
» Airworthiness DirectivesService Bulletin Compliance
» Corrosion ControlAging Aircraft Approved Maintenance Organizations
» Non-Destructive Testing Weight and Balance Control
» BorrowingPooling of Parts Certification of Components
» Storage Facilities Approved Maintenance Organizations
» Category IIIII Maintenance Program
» Extended Range Operations EROPs
» Maintenance Program Maintenance Test and Ferry Flights
» Enroute Inspection Air Operator
» Quality Control Curriculum Common Requirements
» Examination Graduation Certificates Common Requirements
» Instructors Organizational Chart Common Requirements
» Facilities CAR 423.08 3a Common Requirements
» Prerequisites and Curriculum Equipment General Aircraft and Avionics
» Facilities General Aircraft and Avionics
» Reference Material Class Size
» Advisory Committee Basic Training Requirements
» Prerequisites and Curriculum Type Training Requirements
» Equipment Type Training Requirements
» Facilities Type Training Requirements
» Mixing of Adhesives Job Cards
» Cleaning Handling Bonding Process
» Loading of Parts into Fixtures
» Certification and Control of Hot Presses, Autoclaves and Jigs References Curing References
» Inspection of Bonded Parts References
» Cadmium Plating Chemical Milling of Aluminum Alloys
» Chemical Conversion Coatings for Aluminum Alodine: Brush
» ChromicSulphuric Acid Anodizing of Aluminum Copper Plating
» Dichromate Treatment of Magnesium Alloys
» Heat Treatment of Aluminum Alloys Air Furnace Heat Treatment of Aluminum Alloys Salt Bath
» Heat Treatment of Steel Sulphuric AcidSodium Dichromate Etch
» Vapour Degreasing Specification Materials
» Aluminum Brazing Dip Brazing
» Fusion Welding Manufacturing Processes
» Metallic Arc Welding Tungsten Inert Gas TIG Shielded-Arc Welding
» CertificationQualification of NDT Personnel
» Eddy Current Inspection Manufacturing Processes
» Liquid Penetrant Inspection Manufacturing Processes
» Magnetic Particle Inspection Manufacturing Processes
» Radiographic Inspection Manufacturing Processes
» Ultrasonic Inspection Manufacturing Processes
» Non-Conforming Material Review Board MRB
» Special Processes Sub-Contractor and Supplier Control
» Production Control System Manual PCSM
» Control of PartsMaterial Distributors
» Recertification of Components Distributors
» Storage Facilities Facilities Distributors
» Engineering Procedures ManualDesign Approval Procedures EPMDAPM
» Technical PublicationsLibrary Airworthiness Engineering Organization
» Personnel Records Airworthiness Engineering Organization
» Quality Audits Airworthiness Engineering Organization
» Data Review Airworthiness Engineering Organization
» Airworthiness Inspection Representative AIR
» Maintenance Policy Manual MPM
» Engineering - Design, Development and Review
» Personnel Avionics Approved Maintenance Organizations and
» Technical Data Control Avionics Approved Maintenance Organizations and
» Control of PartsMaterial Receiving Inspections
» Sub-Contracting and Supplier Control Testing
» Sample Units for Conformance Sample Aircraft for Conformance if applicable
» StorageQuarantine Avionics Approved Maintenance Organizations and
» Inspection Records Avionics Approved Maintenance Organizations and
» Workshop - General Battery Shop LeadAcid CAA EEL1-1
» Battery Shop Nicad CAA EEL1-3 Shipping
» Technical PublicationLibrary Avionics Approved Maintenance Organizations and
» Software Quality Assurance SQA if applicable Electrostatic Sensitive Device ESD
» Testing and Measuring EquipmentSpecial Tools
» Mandatory Reporting of Defects
» Technical Training Standards Avionics Approved Maintenance Organizations and
» OP-10 Flight Documentation Applicability
» OP-11 Aircraft Inspection OP-12 Aircraft Documentation
» OP-13 Minimum Equipment List OP-14 Cabin Safety
» OP-15 Flight Attendant Training Program
» OP-16 Flight Attendant Training Records
Show more